Verifikační příklady
Software společnosti Dlubal provádí statické výpočty srozumitelnými postupy. Není to žádná „černá skříňka“. Zde uvedené verifikační příklady objasňují podstatu analytických výpočtů a vysvětlují metody posouzení.
Konstrukce se skládá z I-profilu a dvou trubkových nosníků. The structure contains several imperfections and it is loaded by the force Fz. Vlastní tíha se v tomto příkladu nezohledňuje. Determine the deflections uy and uz and axial rotation φx at the endpoint (Point 4). Verifikační příklad vychází z příkladu, který představili Gensichen a Lumpe.
Tento verifikační příklad vychází z verifikačního příkladu 0122. A single-mass system without damping is subjected to an axial loading force. An ideal elastic-plastic material with characteristics is assumed. Determine the time course of the end-point deflection, velocity, and acceleration.
Uvažujeme tuhou lešenářskou trubku, která je ve spodní části fixně podepřena uzlovou podporou pro lešení a zatížena momentem i silou. Calculate the maximum deflection with consideration of initial slippage.
Verifikační příklad popisuje zatížení větrem v několika směrech proudění větru na modelu skupiny budov. The model consists of eight cubes. The velocity fields obtained by the RWIND simulation are compared with the measured values from the experiment. The experimental data are measured using a thermistor anemometer in the wind tunnel.
Stanoví se maximální průhyb a maximální radiální moment prosté kruhové desky namáhané konstantním tlakem, konstantní teplotou a rozdílem teplot.
A long, thin beam is carrying a concentrated mass and is loaded by a time-dependent force. Je prostě podepřený. The problem is described using the following parameters. Determine the deflections in the given test times.
Uvažujeme tuhou lešenářskou trubku, která je ve spodní části fixně podepřena uzlovou podporou pro lešení a zatížena momentem i silou. Calculate the maximum radial deflection by exceeding the capacity of the scaffolding support.
Jednovrstvá čtvercová ortotropní deska je ve svém středu zcela fixována a namáhána tlakem. Porovnejte průhyby rohů desek pro kontrolu správnosti transformace.
Uvažujeme tuhou lešenářskou trubku, která je ve spodní části fixně podepřena uzlovou podporou pro lešení a zatížena momentem i silou. Self-weight is not considered. Considering an infinitely rigid beam, determine the maximum radial deflection.
Ocelový nosník se čtvercovým průřezem je zatížen normálovou silou a spojitým zatížením. The image shows the calculation of the maximum bending deflection and critical load factor according to the second-order analysis.
Hmotový systém s vůlí a dvěma pružinami se nejdříve vychýlí. Determine the natural oscillations of the system - deflection, velocity, and acceleration time course.
Ocelové lano nebo membrána s kolíky na obou koncích jsou zatíženy rovnoměrným zatížením. Neglecting its self-weight, determine the maximum deflection of the structure using the large deformation analysis.
Silnostěnná nádoba je zatížena vnitřním tlakem tak, že nádoba dosáhne pružno-plastického stavu. While neglecting self‑weight, the analytical and numerical solutions for the radial position of the plastic zone border (under the Tresca hypothesis) are determined and compared.
Jednohmotový systém je vystaven zatěžující síle. Determine the deflection of the system.
Konzola z kruhového prutu je zatížena excentrickým rovnoměrným zatížením. Determine the maximum deflection and maximum twist of the console using the geometrically linear analysis.
Na obrázku 1 je znázorněn nosník ASTM A992 W 24×62 se smykem na konci 48 000 a 145 000 kips od vlastní tíhy a užitného zatížení. Verify the available shear strength of the selected beam, based on LRFD and ASD.
A cantilever of rectangular cross‑section has a mass at the end. Kromě toho je zatížena normálovou silou. Calculate the natural frequency of the structure. Neglect the self‑weight of the cantilever and consider the influence of the axial force for the stiffness modification.
Stanovíme maximální průhyb krychle. The cube's lower side is fully fixed and the upper side is subjected to shear loading.
Stanovte maximální průhyby bloku se zohledněním nebo zanedbáním smykového účinku. The square block of the isotropic material is fully fixed at one end and loaded with uniform vertical pressure.
Tlumený jednohmotový systém je zatížen konstantní silou. Determine the spring force, damping force, and inertial force at the given test time. In this verification example, the Kelvin--Voigt dashpot (namely, a spring and a damper element in serial connection) is decomposed into its purely viscous and purely elastic parts, in order to better evaluate the reaction forces.
Konzola je plně fixována na levém konci a zatížena příčnou silou a normálovou silou na pravém konci. The tensile strength is zero and the behavior in the compression remains elastic.
Stanoví se maximální průhyb a napětí ve směru z spřažené desky, která se skládá ze dvou skleněných vrstev a jedné vrstvy fólie mezi nimi a je vystavena konstantnímu tlaku.
A membrane is stretched by means of isotropic prestress between two radii of two concentric cylinders not lying in a plane parallel to the vertical axis. Find the final minimum shape of the membrane - the helicoid - and determine the surface area of the resulting membrane. K tomu slouží přídavný modul RF-FORM-FINDING. Elastic deformations are neglected both in RF-FORM-FINDING and in the analytical solution; self-weight is also neglected in this example.
Prut s W-profilem podle ASTM A992 je vybrán tak, aby unesl vlastní tíhu 30 000 kips a užitné zatížení 90 000 kips v tahu. Verify the member strength using both LRFD and ASD.
Ověřte, zda nosník různých průřezů ze slitiny 6061-T6 odpovídá požadovanému zatížení podle Aluminum Design Manual 2020.
Konzola je plně fixována na levém konci a zatížena ohybovým momentem na pravém konci. Materiál má různé plastické pevnosti v tahu a tlaku.
Spřažená deska sestávající ze tří skleněných vrstev, jedné vrstvy fólie a vnitřního prostoru se suchým vzduchem je plně upevněna a zatížena proměnnou teplotou. Neglecting its self-weight, determine the plate's maximum deflection.
Cílem tohoto příkladu je předvést nevratný děj způsobený třením. After the loading and unloading, the end-point is in a different position than where it was at the beginning. Determine the movement of the node in the X direction.
A compact disc (CD) rotates at a speed of 10,000 rpm. Je tak vystaven odstředivé síle. The problem is modeled as a quarter model. Determine the tangential stress on the inner and outer diameters and the radial deflection of the outer radius.
Dvouvrstvá silnostěnná nádoba s otevřeným koncem je zatížena vnitřním a vnějším tlakem; proto nevzniká žádné osové napětí. While neglecting self‑weight, the radial deflection of the inner and outer radius, and the pressure (radial stress) in the middle radius is determined.