The structural analysis software RFEM 6 is the basis of a modular software system. The main program RFEM 6 is used to define structures, materials, and loads of planar and spatial structural systems consisting of plates, walls, shells, and members. The program also allows you to create combined structures as well as to model solid and contact elements.
RSTAB 9 is a powerful analysis and design software for 3D beam, frame, or truss structure calculations, reflecting the current state of the art and helping structural engineers meet requirements in modern civil engineering.
Do you often spend too long calculating cross-sections? Dlubal Software and the RSECTION stand-alone program facilitate your work by determining section properties of various cross-sections and performing a subsequent stress analysis.
Do you always know where the wind is blowing from? From the direction of innovation, of course! With RWIND 2, you have a program at your side that uses a digital wind tunnel for the numerical simulation of wind flows. The program simulates these flows around any building geometry and determines the wind loads on the surfaces.
Are you looking for an overview of snow load zones, wind zones, and seismic zones? Then you are in the right place. Use the Geo-Zone Tool to determine quickly and efficiently snow loads, wind speeds, and seismic data according to ASCE 7‑16 and other international standards.
Would you like to try out the capabilities of the Dlubal Software programs? You have the opportunity to do so! The free 90-day full version allows you to thoroughly test all our programs.
The Masonry Design add-on allows you to automatically determine the stiffness of your wall-slab hinge. The diagrams were determined as part of the research project DDmaS - "Digitizing the design of masonry structures" and are derived from the standard.
Define a line hinge on the connection line of both surfaces and activate the slab-wall connection.
You can now enter your parameters in the Slab-Wall Connection tab. Then, click the Regenerate [...] button.
The determined diagrams are displayed subsequently.
All members when using the Design Add-ons for serviceability checks are considered supported at the end nodes by default. If the member is instead a cantilever or includes an internal support for a combination of both a cantilever and supported at both ends member type, a new Design Support should be defined under the member details.
The Design Support option can be found under the member dialog box under Design Supports & Deflection tab. Supports can be added to any nodes detected along the member length such as the member start, member end, or internal nodes.
Under the New Design Support dialog box, you can set the type of support from the drop-down including general, concrete, or timber. The "general" will give the program guidance on the deflection member type and which limiting deflection ratio to reference from the Serviceability Configurations whether cantilever (e.g., L/180) or supported on both ends (e.g., L/360). The alternative types "concrete" and "timber" will also influence the deflection design, but have additional strength design options incorporated such as moment and shear internal force modification for concrete design and a stress perpendicular to grain check for timber design.
For additional detailed information on this new setting in RFEM 6 including a "timber" type design support, refer to the webinar listed below under Links at time 51:05.
Some materials have multiple limit stress limits for compression, tension, and so on. For these materials, the limiting stress must be input manually by the user.
The limit stress values are listed under the Material Values tab.
These values can be added in the Member/Surface Configurations under the User limit stress type.
You can also define structural modifications in a load case of the Modal Analysis type. Thus, you can access the stiffness modifications of the individual objects and deactivate the selected objects, if necessary.
In order to display the mode shapes of your dynamic analysis, you have to create a load case of the Modal Analysis type and specify your settings for the modal analysis there.
After the calculation, you can evaluate your results in the Results navigator. You can see further information in the table.
You can adjust the display of the mode shape normalization directly in the Results navigator. If the setting is changed, no recalculation is necessary.
Depending on the setting, the largest displacement or deformation represents the reference value 1, to which the other results are scaled.
The Building Model and the feature of modeling stories with "Rigid Diaphragm" is not designed for all building types.
The function was primarily developed for 3D buildings with 5-10 stories (or more) with a regular or the same floor plan. This means that you should only assign the "Rigid Diaphragm" function to the slabs where the walls and columns are positioned identically in the stories above and below. If this is not the case, instability may occur.
If the model has been entered correctly according to this convention, three options for the result display will be available to you:
The "Total" result display shows the results on the entire vertical components (that is, walls, shear walls, columns, and so on). See Image 02. If you select "Floors only", the results for the separate calculation of slabs are displayed as a 2D model. The "Combination" option corresponds to the same results from both result types mentioned above.
For smaller 3D models and buildings with different floor plans, it is still better to work with the usual modeling as a 3D model. If you are working with models that sometimes have regular floor plans, you can alternatively assign the "Rigid Diaphragm" option to the individual floor slabs. The floor plan geometry of the stories above and below this slab should then be the same again.
The fundamental extraction of a 2D floor from any 3D model is not possible with the technology implemented for this add-on function.
To perform an earthquake analysis, you need a modal analysis and then a load case of the Response Spectrum Analysis type.
After you have performed your modal analysis, create a new load case. Here you will find the usual settings from the previous program generation.
In the Response Spectrum tab, you can define your response spectrum as usual. If you want to use a response spectrum according to the standard, make sure that the desired standard is selected in the general data of Standards II.
In the Selection of Modes tab, you can select the mode shapes and filter them, if necessary.
After the load case has been calculated, you obtain the results.
In the modal analysis settings, you can set the minimum axial strain for cables and membranes in order to apply an initial prestress to the objects and thus improve the convergence of the calculation. The initial prestress is applied to the objects in a simplified approach.
If you compare this setting with a surface load of the Axial Strain load type, you should pay attention to the fact that the two approaches differ. With the surface load, you perform a calculation in such a way that the actual prestress can deviate from the specified prestress. The calculation also takes into account other boundary conditions, such as the Poisson's ratio of the material.
You can easily check this if you vary the Poisson's ratio of the material. A Poisson's ratio other than 0 causes the deformation to interact in the x- and y-directions of the surface, which no longer results in a constant stress/strain over the entire surface.
If the Poisson's ratio is 0, you obtain the same results.