Walec wykonany z gruntu sprężysto-plastycznego jest poddawany trójosiowym warunkom testowym. Celem jest określenie granicznego naprężenia pionowego dla zniszczenia naprężenia od ścinania, pomijając ciężar własny. Uwzględniane jest początkowe naprężenie hydrostatyczne 100 kPa.
Określ dopuszczalną wytrzymałość na ściskanie osiowe belki o długości 2,2 m i przekroju różnych przekrojów, wykonanej ze stopu 6061-T6 i zabezpieczonej bocznie w celu zapobiegania wyboczeniu względem słabej osi zgodnie z Instrukcją projektowania konstrukcji aluminiowych 2020.
Należy sprawdzić, czy belka o różnych przekrojach wykonana ze Stopu 6061-T6 jest odpowiednia do wymaganego obciążenia, zgodnie z Aluminium Design Manual (Podręcznik projektowania konstrukcji aluminiowych 2020).
Zgodnie z DIN EN 1992-1-1/NA/A1:2015, na podstawie 1990-1-1/NA/A1:2012-08 słup z betonu zbrojonego jest projektowany pod kątem SGN w temperaturze normalnej. W obliczeniach zastosowano metodę krzywizny nominalnej; patrz DIN EN 1992-1-1, rozdział 5.8.8. Zaadresowany słup znajduje się na krawędzi trzyprzęsłowej konstrukcji ramowej, która składa się z 4 słupów wspornikowych i 3 pojedynczych kratownic połączonych przegubowo z nimi. Na słup działa siła pionowa prefabrykowanej kratownicy, śnieg i wiatr. Wyniki porównano z literaturą.
Korzystając z tabel ręcznych AISC, należy określić dostępne wytrzymałości na ściskanie i zginanie oraz czy belka ASTM A992 W14x99 ma wystarczającą wytrzymałość, aby przenieść siły osiowe i momenty pokazane na rysunku 1, uzyskane w analizie drugiego rzędu z uwzględnieniem efektów P-𝛿.
Na rysunku 1 pokazano belkę ASTM A992 W 24x62 o skróceniu do ścinania na końcu 48 000 i 145 000 kips od obciążeń stałych i użytkowych, odpowiednio Sprawdź dostępną wytrzymałość na ścinanie wybranej belki na podstawie LRFD i ASD.
Rozważ belkę ASTM A992 W 18x50 dla stałych i równomiernych obciążeń stałych i ruchomych, jak pokazano na Rysunku 1. Pręt jest ograniczony do maksymalnej nominalnej głębokości wynoszącej 18 cali. Ugięcie pod obciążeniem użytkowym jest ograniczone do L/360. Belka jest swobodnie podparta i usztywniona. Sprawdź dostępną wytrzymałość na zginanie wybranej belki na podstawie LRFD i ASD.
Słup w kształcie litery W zgodny z normą ASTM A992 14x132 jest obciążony zadanymi osiowymi siłami ściskającymi. Słup jest przegubowy na górze i na dole w obu osiach. Należy określić, czy słup jest w stanie wytrzymać obciążenie pokazane na rysunku 1 na podstawie LRFD i ASD.
Wybrano pręt w kształcie litery W zgodny z ASTM A992 tak, aby przeniósł ciężar własny 30 000 kN i obciążenie rozciągające 90 000 kN. Sprawdź wytrzymałość pręta za pomocą LRFD i ASD.
Za pomocą LRFD i ASD należy określić wymagane wytrzymałości i współczynniki długości efektywnej dla słupów z materiału ASTM A992 w ramie skręcania pokazanej na rysunku 1 dla maksymalnej kombinacji obciążeń grawitacyjnych.
Osiadania sztywnego fundamentu kwadratowego na glinie jeziornej [1] są obliczane w programie RFEM. Modelowana jest jedna czwarta fundamentu. Fundament ma szerokość 75,0 m po obu stronach. Do wygenerowania wyników wykorzystywane są etapy budowy.
Model oparty jest na przykładzie 4 z [1]: Płyta podparta punktowo.
Należy zaprojektować płaską płytę budynku biurowego o wrażliwych na zarysowania ścianach lekkich. Należy zbadać panele wewnętrzne, brzegowe i narożne. Słupy i płyta są połączone monolitycznie. Słupy skrajne i narożne są zlicowane z krawędzią płyty. Osie słupów tworzą siatkę kwadratową. Jest to układ sztywny (budynek usztywniony ścianami usztywniającymi).
Budynek biurowy ma 5 kondygnacji i ma wysokość 3.000 m. Warunki środowiskowe, które należy przyjąć, określane są jako „zamknięte przestrzenie wewnętrzne”. Występują głównie oddziaływania statyczne.
Celem tego przykładu jest określenie momentów w płycie i wymaganego zbrojenia nad słupami przy pełnym obciążeniu.
Model oparty jest na przykładzie 4 z [1]: Płyta podparta punktowo. Siły wewnętrzne i wymagane zbrojenie podłużne można znaleźć w przykładzie weryfikacji 1022. W tym przykładzie przebijanie jest rozpatrywane w osi B/2.
W tym przykładzie ścinanie na granicy między betonem wylanym w różnym czasie a odpowiednim zbrojeniem jest określane zgodnie z DIN EN 1992-1-1. Wyniki uzyskane w programie RFEM 6 zostaną porównane z poniższymi obliczeniami ręcznymi.
W tym przykładzie obliczeniowym obliczane są wartości nośności sił tnących na belkach zgodnie z EN 1998-1, 5.4.2.2 i 5.5.2.1 oraz nośność słupów przy zginaniu zgodnie z 5.2.3.3(2 ). System składa się z dwuprzęsłowej belki żelbetowej o rozpiętości 5,50 m. Belka jest częścią układu ramowego. Otrzymane wyniki są porównywane z wynikami w [1].
Belka żelbetowa została zaprojektowana jako belka dwuprzęsłowa na wsporniku. Przekrój zmienia się na całej długości wspornika (przekrój o zmiennym przekroju). Obliczane są siły wewnętrzne oraz wymagane zbrojenie podłużne i zbrojenie na ścinanie dla stanu granicznego nośności.