Co oznaczają informacje projektowe: Błąd geometrii po lewej stronie: Blacha czołowa dźwigara: Lambda2>1,4 Półka słupa: Lambda2>1,4 Nie mogę znaleźć żadnego wyjaśnienia w instrukcji ani w Internecie.
Czy posiadają Państwo program do wymiarowania słupów zamocowanych w betonie? Nie chodzi o zaprojektowanie kielicha, ale o wymaganą głębokość osadzenia, przewidziane naprężenie w betonie, kontrolę naprężenia ścinającego w słupie i tak dalej.
Chciałbym przeprowadzić obliczenia odporności ogniowej przy użyciu modułu dodatkowego EC3. Czy jest możliwość takiej ingerencji w program, aby zamiast standardowej wykorzystać własną krzywą temperatury?
Do obliczeń aktywowałem opcję "Obliczenia szczegółowe". Czy obciążenia podporowe ze zredukowanym współczynnikiem dynamicznym zostały już określone do wymiarowania konstrukcji nośnej?
Użyłem podwójnych prętów do wprowadzania prętów. Czy muszę brać pod uwagę coś jeszcze, czy może lepiej wprowadzić pręt o podwójnych właściwościach przekroju?
W przypadku obliczeń odporności ogniowej moduł sprężystości jest redukowany. Zakładam, że w pierwszej kolejności dotyczy to projektu. Jednak w jakim stopniu uwzględniana jest zmiana sztywności w układzie konstrukcyjnym, a tym samym redystrybucja obciążenia?
Muszę zwymiarować wspornik ścienny wykonany ze stalowych wsporników, który zamodelowałem jako komponenty powierzchniowe w programie RFEM 5. Z którego modułu mogę skorzystać?
Chciałbym zaprojektować poręcze, dlatego stworzyłem zestaw prętów. Przekrój jest przekrojem zamkniętym. Czy analizę stateczności można przeprowadzić na całej konstrukcji, czy też muszę przeliczyć ją z danymi wszystkich podpór na wymiarowanie pręta zastępczego w programie STEEL EC3?
W jaki sposób mogę określić, czy na potrzeby obliczeń współczynnika redukcyjnego dla wyboczenia ścinania w PLATE-BUCKLING występuje element usztywniający sztywny czy niesztywny?
Utworzyłem ramę 2D i chciałbym przypisać do kalenicy utwierdzenie boczne i skrętne. Czy w programie RF-/STEEL EC3 muszę wprowadzać pośrednie utwierdzenie boczne lub podporę węzłową?
Przeprowadzam analizę stateczności zgodnie z analizą drugiego rzędu. Dlaczego do analizy naprężeń wykorzystywany jest tutaj częściowy współczynnik bezpieczeństwa γM1?
Podczas obliczeń otrzymuję ostrzeżenie, że niektóre elementy są połączone z panelem wyboczeniowym, ale nie są zdefiniowane jak usztywnienia (patrz rysunek 01). Co mam zrobić?
Podczas obliczania połączenia za pomocą modułu rozszerzającego FRAME‑JOINT Pro pojawia się komunikat, że wartość jest poza dopuszczalnym zakresem (istniejący Wartość: 160, wartość minimalna 200). Co oznacza ta wiadomość?
Podczas określania efektywnych właściwości przekroju zgodnie z EN 1993-1-1, EN 1993-1-5 lub EN 1999-1-1, SHAPE-THIN wyświetla ostrzeżenie, że szerokości efektywne są określane tylko dla elementów prostych. Co to oznacza?
Jakie są możliwości programu RFEM 5 lub RSTAB 8, aby określić sprężysty moment krytyczny zwichrzenia dowolnych przekrojów, układów lub obciążeń? Czy możliwe jest zaprojektowanie płaskiej konstrukcji stalowej (wsporniki, stalowe podłużnice schodów)?
Projektując belkę, chciałbym pominąć skręcanie uwzględnione w analizie stateczności za pomocą filtrów opisanych w artykule nr 001498 w Bazie informacji.
Definiuję filtr, ale ostrzeżenie o skręcaniu pojawia się ponownie w tym samym miejscu x. Czy obliczeniowe siły wewnętrzne ulegają zmianie, czy też dlaczego?