110 Wyniki
Wyświetl wyniki:
Sortuj według:
Uwzględnienie mimośrodu spoiny w RFEM 6
Czy możliwe jest uwzględnienie mimośrodu niesymetrycznych spoin liniowych do obliczeń naprężeń w programie RFEM 6?
Analiza stateczności zgodnie z EN 1993-1-1
Czy w RSECTION 1 można przeprowadzić analizy stateczności zgodnie z EN 1993-1-1?
Usztywnienia na pasach dźwigarów w połączeniu z ramą sztywną
W jaki sposób usztywnienia na zewnętrznych krawędziach pasów belki połączenia sztywnego ramy wpływają na maksymalny przenoszony moment oraz na sztywność obrotową i powiązane przemieszczenia konstrukcji ramy?
Metoda elementów skończonych oparta na komponentach (CBFEM) w RFEM 6
Co to jest metoda elementów skończonych oparta na komponentach (CBFEM)?
Obliczanie stalowych konstrukcji hydraulicznych
Czy mogę analizować i wymiarować stalowe konstrukcje hydrauliczne za pomocą programów Dlubal?
Programy do konstrukcji drewnianych warstwowych i klejonych krzyżowo
Jakich programów potrzebuję do pracy z konstrukcjami warstwowymi lub drewnem klejonym krzyżowo (CLT)?
Przekrój efektywny
Czy mogę obliczyć efektywne właściwości przekroju za pomocą RSECTION?
Rura jako klucz ścinania w module dodatkowym RF-/JOINTS Steel - Column Base
Jak wybrać rurę jako klucz do ścinania w module dodatkowym RF-/JOINTS Steel - Column Base?
- 005450
- RFEM 6
- RSTAB 9
-
- Projektowanie konstrukcji stalowych RFEM 6
- Projektowanie konstrukcji stalowych RSTAB 9
- Projektowanie konstrukcji aluminiowych RFEM 6
- Projektowanie konstrukcji aluminiowych RSTAB 9
- Form-Finding RFEM 6
- Konstrukcje stalowe
- Lekkie konstrukcje aluminiowe
- Konstrukcje tymczasowe
- Rozciągane konstrukcje membranowe
- Analiza statyczno-wytrzymałościowa
- Form-Finding i szablony cięcia
- Analiza dynamiczna i sejsmiczna
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM
Konstrukcje tymczasowe
Chciałbym przeprowadzić analizę konstrukcji tymczasowych. Jakie programy polecacie?
Pytanie
Kopiuję przypadek obliczeniowy i/lub wybieram inny lub kolejny węzeł do obliczeń. Geometria połączenia zdefiniowana w poprzednim przypadku obliczeniowym nie jest jednak przenoszona. Jaki jest tego powód?
Pytanie
Co oznaczają informacje projektowe:
Błąd geometrii po lewej stronie:
Blacha czołowa dźwigara: Lambda2>1,4
Półka słupa: Lambda2>1,4
Nie mogę znaleźć żadnego wyjaśnienia w instrukcji ani w Internecie.
- 005437
- RFEM 6
- RSTAB 9
-
- Projektowanie konstrukcji stalowych RFEM 6
- Projektowanie konstrukcji stalowych RSTAB 9
- Połączenia stalowe RFEM 6
- Skręcanie skrępowane (7 stopni swobody) RFEM 6
- Skręcanie skrępowane (7 stopni swobody) RSTAB 9
- Konstrukcje stalowe
- Analiza statyczno-wytrzymałościowa
- Analiza naprężeń
- Sprawdzenie stateczności
- Analiza skręcania skrępowanego
- Połączenia stalowe
- Profile formowane na zimno
- Eurocode 3
- ANSI/AISC 360
- CSA S16
- IS 800
- GB 50017
- SP 63.13330
- BS 5950-1
- AS 4100
- SIA 263