The structural analysis software RFEM 6 is the basis of a modular software system. The main program RFEM 6 is used to define structures, materials, and loads of planar and spatial structural systems consisting of plates, walls, shells, and members. The program also allows you to create combined structures as well as to model solid and contact elements.
RSTAB 9 is a powerful analysis and design software for 3D beam, frame, or truss structure calculations, reflecting the current state of the art and helping structural engineers meet requirements in modern civil engineering.
Do you often spend too long calculating cross-sections? Dlubal Software and the RSECTION stand-alone program facilitate your work by determining section properties of various cross-sections and performing a subsequent stress analysis.
Do you always know where the wind is blowing from? From the direction of innovation, of course! With RWIND 2, you have a program at your side that uses a digital wind tunnel for the numerical simulation of wind flows. The program simulates these flows around any building geometry and determines the wind loads on the surfaces.
Are you looking for an overview of snow load zones, wind zones, and seismic zones? Then you are in the right place. Use the Geo-Zone Tool to determine quickly and efficiently snow loads, wind speeds, and seismic data according to ASCE 7‑16 and other international standards.
Would you like to try out the capabilities of the Dlubal Software programs? You have the opportunity to do so! The free 90-day full version allows you to thoroughly test all our programs.
In this webinar, you will learn how to perform linear stability analyses in RFEM 6 and RSTAB 9.
In this webinar, you will learn how to calculate reinforced concrete slabs in RFEM 6.
In this webinar, you will learn how to design a tent hall consisting of aluminum cross-sections in RFEM 6.
In this webinar, we show you how to analyze machine-induced vibrations using the Time History Analysis add-on.
In this webinar, we show you how to perform seismic designs for reinforced concrete structures in RFEM 6.
In this webinar, we show you how to create cold-formed steel sections in RSECTION and how to design them in RFEM 6 / RSTAB 9.
In this webinar, we use an example to explain how you can model and analyze solid elements in RFEM 6
Free Webinar | Stability Analysis in RFEM 6 (USA)
This webinar will provide an introduction to stability analysis in RFEM 6.
In this webinar, we show you how to model walls made of masonry in RFEM 6 and how to design them using the Finite Element Analysis (FEA).
In this webinar, we show you how to perform design checks for plate and shell buckling in RFEM 6 according to Eurocode 3.
In this webinar, we show you how to define the shear and longitudinal reinforcement for a concrete section in RSECTION and how to design the reinforced RSECTION section in RFEM 6.
This webinar shows you how to model and design structural elements made of fiber-reinforced concrete (FCR) using the Concrete Design add-on.
Free Webinar | CSA A23.3:19 Concrete Building Design in RFEM 6 (USA)
This webinar will provide an introduction to concrete building design acc. to the CSA A23.3:19 in RFEM 6.
Free Webinar | Steel Silo Design in RFEM 6 (USA)
This webinar will provide an introduction to steel silo design in RFEM 6.
In this webinar, we show you some new features that have recently been added to the Concrete Design add-on for RFEM 6 and RSTAB 9.
This webinar shows how to perform stability and warping torsion analyses for steel structures in RFEM 6 and RSTAB 9.
Free Webinar | Reinforced Concrete Tank Design in RFEM 6 (USA)
This webinar will provide an introduction to reinforced concrete tank analysis and design in RFEM 6.
This webinar provides an introduction to aluminum modeling and design in RFEM 6 and RSTAB 9.
This webinar provides an introduction to the design of aluminum structures in RFEM 6 and RSTAB 9.
Webinars provide the opportunity to gain expert knowledge and to ensure you’re getting the most out of your Dlubal programs.
Free Webinar | ADM 2020 Aluminum Design in RFEM 6 (USA)
This webinar will provide an introduction to aluminum member design acc. to the ADM 2020 in RFEM 6.