25 Results
View Results:
Sort by:
Question
Why it is not possible to design a biaxial bending with the RF‑/JOINTS add-on module?
Question
How do I superimpose generated equivalent loads from the seismic analysis?
Question
Why do the results of members and sets of members differ in the design?
Question
Are the models and presentations from Info Day 2019 freely available, and can you send them to me?
Question
How do I determine the stiffness center of my structural system?
Question
When determining the effective cross-section properties according to EN 1993‑1‑1, EN 1993‑1‑5, or EN 1999̩1‑1, SHAPE‑THIN displays a warning message saying that the effective widths are only determined for straight elements. What does this mean?
Question
Which result combinations can I design with the RF‑/JOINTS Pro program, and what should I pay attention to?
Question
Can I rotate a foundation about the Z-axis in the RF‑FOUNDATION Pro add-on module?
Question
Is there a way to prepare an EC3 buckling check without setting the intermediate support manually, or is there a workaround that can speed this up?
Question
Is the Gust-effect (G or Gf) from the ASCE 7‑16 Sect. 26.11 considered in RWIND Simulation?
Question
I need to define different types of lateral intermediate restrains for a single element in RF-/STEEL EC3. Is this possible?
Question
What is the formula used to calculate the ASCE 7 wind velocity profile?
Question
How can I enter or read out a response spectrum via the COM interface in DYNAM Pro?
- 004727
- RFEM 5
- RSTAB 8
-
- Concrete Structures
- Steel Structures
- Timber Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Finite Element Analysis
- Wind Simulation & Wind Load Generation
- Stability Analysis
- Dynamic and Seismic Analysis
- Form-Finding and Cutting Patterns
- Cold-Formed Sections
- Eurocode 1
- Eurocode 3
- Eurocode 5
Question
Are the models and presentations from Info Day 2020 freely available, and can you send them to me?
Question
How can I create a drilled beam in RFEM?
Question
What should be considered when using a failure of columns under tension in the RF‑/DYNAM Pro – Equivalent Loads add-on module?
Imperfection from Mode Shape
How do I create an imperfection based on a mode shape in RFEM 6?
Redundancy Factors
How do I include the redundancy factor(s) ρ in the ASCE 7 load combinations?
Overstrength Factors
How do I include the overstrength factor(s) Ωo in the ASCE 7 load combinations?
Standardized Sections for AISI Design
Which standardized sections are valid for AISI cold-formed steel design in RFEM 6?
Custom Sections for AISI Design
Can I design user-defined (parametric) sections according to AISI S100 or CSA S136?
AISI Table B4.1-1 Applicability Limits
Does RFEM check the applicability limits of AISI Table B4.1‑1?
Cable and Tensile Structures
I would like to analyze cable and tensile structures. Is it possible to use RFEM or RSTAB for this?
Aluminum and Lightweight Structures
I would like to design an aluminum structure. Is it possible to use RFEM or RSTAB for this?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM