34 Results
View results:
Sort by:
Automatic Reinforcement Design
Can the RFEM 6 Concrete Design add-on automatically design member and surface reinforcement?
Is the deformation analysis in state II included in the concrete design in RFEM 6?
Is the deformation analysis in state II included in the concrete design in RFEM 6?
Member Design Supports for Deflection Checks
How do I define a member as a cantilever and not as supported at both ends for serviceability or deflection design?
Results of Punching | Concrete design in RFEM 6
Where can I find the graphical results of punching shear in the concrete design? Especially the distribution of shear forces at the critical perimeter or the punching loads.
Stiffness Modulus Method
Is it possible to perform an analysis according to the stiffness modulus method in RFEM or RSTAB?
How can I open the interaction diagram from Concrete Design?
How can I open the interaction diagram from Concrete Design?
Why are the members not valid for the Concrete Design add-on?
Why are the members not valid for the Concrete Design add-on?
Is it possible to design single-layer reinforced surfaces with RFEM 6?
Is it possible to design single-layer reinforced surfaces with RFEM 6?
Not Covered Reinforcement on Members | Concrete Design in RFEM 6 and RSTAB 9
Although all the member design checks have been fulfilled, I get the "Not Covered Reinforcement" result. What is the reason?
Uneven Terrain
The terrain surface of my soil to be analyzed is uneven. How can I edit the geometry of my soil massif for the modeling?
Nominal Reinforcement Bar Size
Can I define a different bar size in the RFEM 6 Concrete Design add-on other than the default bar sizes available in the drop-down?
Punching
I would like to perform punching design of a floor slab. I have selected nodes for the design, but they are marked as invalid. Where did I make a mistake?
Creep and Shrinkage of Concrete
Where can I activate creep or shrinkage for concrete design?
How can I check the way RFEM 6 determines the required reinforcement?
How can I check the way RFEM 6 determines the required reinforcement?
Case-Related Design with Different Load Situations
How can I carry out case-related design for different load situations?
Construction Stages - Modifying Properties
Is it possible to change the properties of members or surfaces, such as their location, in the individual construction stages?
Small Cohesion for Non-Cohesive Soils
What value can I use for cohesion in order to avoid singularities?
Surface Reinforcement in Rib Design
How do I consider the surface (slab) reinforcement in my rib member (T-beam) design?
Creating User-Defined Fabric
How do I create a user-defined fabric?
Membrane Structures
Is it possible also to design membrane structures in RFEM?
Setting Deformations to 0
How can I set the deformations from an LC/CO or a construction stage to 0?
Activating Geotechnical Analysis Add-on
I have a license for the Geotechnical Analysis add-on and it appears as available to me. However, I cannot activate it. What could be the reason?
Activating Steel Fiber Concrete Design in "Concrete Design" Add-on
How can I activate the design with steel fiber-reinforced concrete in the "Concrete Design" add-on for RFEM 6?
Graphic Templates for Printing Reinforcement Layout
How can I use graphic templates for multi printing of a reinforcement?
Not Valid/Deactivated Punching Nodes
In the table of the objects to be designed in the Concrete Design add-on, punching nodes are listed in the not valid/deactivated column, although I have defined them as punching nodes. How can I fix this?
Cable and Tensile Structures
I would like to analyze cable and tensile structures. Is it possible to use RFEM or RSTAB for this?
Geotechnical Analysis and Load Cases
I want to consider the soil-structure interaction using one of the nonlinear soil material models. Why is it not reasonable to calculate the individual load cases with this model?
Design Cases
Can I use design cases in RFEM 6 in the same way as in RFEM 5?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM