Zwolnienia węzłowe są to specjalne obiekty w programie RFEM 6, które umożliwiają konstrukcyjne odłączenie obiektów dołączonych do węzła. Zwolnienie jest sterowane przez warunki typu zwolnienia, które również mogą mieć właściwości nieliniowe. W tym artykule przedstawiono definicję zwolnień węzłowych na praktycznym przykładzie.
Norma ASCE 7-16 wymaga zastosowania zarówno zrównoważonych, jak i niezrównoważonych obciążeń śniegiem, do uwzględnienia w obliczeniach konstrukcji. Podczas gdy może to być bardziej intuicyjne w przypadku dachów płaskich, a nawet dwuspadowych/czterospadowych, określenie obciążeń śniegiem jest coraz trudniejsze w przypadku dachów łukowych ze względu na złożoną geometrię. Jednak dzięki wytycznych z ASCE 7-16 na temat obliczeń obciążenia śniegiem zakrzywionych dachów oraz efektywnym narzędziom RFEM do przypisywania obciążeń, możliwe jest uwzględnienie zarówno zrównoważonych, jak i niezrównoważonych obciążeń śniegiem w celu niezawodnego i bezpiecznego wymiarowania konstrukcji.
Zbrojenie konstrukcyjne zgodnie z EN 1992-1-1 9.2.1 zapobiegające kruchemu zniszczeniu elementu. Konstrukcja nie powinna ulec uszkodzeniu bez wcześniejszego komunikatu. Niezależnie od wartości obciążenia, należy zastosować minimalne zbrojenie.
Warunki brzegowe dla podpory płytowej można szybko wprowadzić w programie MES jako podpory osobliwe i liniowe. Jeżeli jednak podczas modelowania konstrukcji nie zostanie uwzględniona podatność podpór, często konieczne jest przyjrzenie się zdefiniowaniom podpór, najpóźniej podczas obliczeń, przy użyciu naprężeń lub podczas określania wymaganego zbrojenia.
W RF-CONCRETE Surfaces powierzchnie zbrojenia siatkowego dla zbrojenia podstawowego i dodatkowego nie są wprowadzane ręcznie, ale można je wybrać z biblioteki. Dafür stehen verschiedene Lieferprogramme zur Verfügung, beispielsweise aus Deutschland, Österreich oder den USA.
Podczas obliczania zbrojenia powierzchni w RF-CONCRETE Surfaces dostępne są wartości wyników dla stron powierzchni +/- z. W poprzednim poście opisano, jak wyświetlić lokalne strony powierzchni w programie RFEM.
Wyniki RF‑CONCRETE Surfaces można udokumentować graficznie w raporcie. Oftmals wird dafür auch die Einstellung "Werte an Flächen" im Ergebnis-Navigator von RF-BETON Flächen angewählt. Hierbei wird eine Textblase mit dem Ergebniswert, abhängig von der Einstellung im Ergebnis-Navigator, entweder an den Rasterpunkten der Fläche beziehungsweise manuell gesetzten Punkten oder in den FE-Netz-Punkten angezeigt.
Bemessen werden soll ein Montagestoß aus Hohlprofilen mit Stirnplatten. Es handelt sich hierbei um den Untergurt eines Fachwerkträgers, welcher aus Transportgründen geteilt werden muss.
Rozszerzenie Projektowanie konstrukcji aluminiowych dla RFEM 6 wymiaruje pręty aluminiowe ze względu na stan graniczny nośności i użytkowalności zgodnie z Eurokodem 9. Ponadto możliwe jest wymiarowanie zgodnie z ADM 2020 (norma amerykańska).
Podczas obliczania regularnych konstrukcji wprowadzanie danych często nie jest skomplikowane, ale czasochłonne. Oszczędzaj cenny czas dzięki automatycznemu wprowadzaniu danych. W niniejszym przypadku należy uwzględnić kondygnacje domu jako poszczególne etapy budowy. Dane są wprowadzane przy pomocy programu w języku C#, aby użytkownik nie musiał ręcznie wprowadzać elementów poszczególnych pięter.
Webservice to komunikacja między maszynami i programami. Komunikacja ta odbywa się za pośrednictwem sieci i dlatego może być wykorzystywana przez dowolny program, który może wysyłać i odbierać ciągi znaków za pośrednictwem protokołu HTTP. Programy RFEM 6 i RSTAB 9 zapewniają interfejs oparty na tych wieloplatformowych usługach sieciowych. Ten tutorial pokazuje podstawy korzystania z języka programowania VBA.
Kriechen und Schwinden des Betons sind Verformungseigenschaften des Betons, welche bei der Bemessung im Grenzzustand der Gebrauchstauglichkeit in der Regel zu berücksichtigen sind.
Moduł RF-CONCRETE Surfaces umożliwia wymiarowanie powierzchni z betonu zbrojonego (ściany, stropy, płyty fundamentowe) zgodnie z ACI 318-19 lub CSA A23.3-19. Powszechnym podejściem przy wymiarowaniu płyt jest zastosowanie pasm obliczeniowych do określenia średnich sił wewnętrznych w danym kierunku na szerokości pasma. Metoda ta sprowadza się zasadniczo do analizy elementu dwukierunkowo zbrojonego jako wydzielonych elementów jednokierunkowo zbrojonych, aby określić wymagane zbrojenie wzdłuż danego pasma.
Wraz z wersją 5.06, moduły RF-CONCRETE Surfaces i RF-CONCRETE Members przeprowadzają automatycznie obliczenia w stanie granicznym użytkowalności, zgodnie z obliczonymi przypadkami obciążeń oraz kombinacjami obciążeń i wyników.
W programie RFEM można wyświetlić wartości wyników dla powierzchni (na przykład z RF-CONCRETE Surfaces), które mogą określić wymagane zbrojenie obliczanych powierzchni w punktach rastra. Zazwyczaj wartości wyników wyświetlane są początkowo dla wszystkich obliczanych powierzchni.
RF-MOVE Surfaces ułatwia generowanie przypadków obciążeń z różnych pozycji obciążeń ruchomych. Dla programu RFEM 5 generowane są oddzielne przypadki obciążeń na podstawie pozycji obciążenia ruchomego. Opcjonalnie generowana jest też obwiednia kombinacji wyników obejmująca wszystkie pozycje obciążenia.
Jakość analizy statyczno-wytrzymałościowej budynków jest dużo lepsza, gdy można uwzględnić warunki gruntowe w sposób możliwie najbardziej realistyczny. W programie RFEM 6 można realistycznie określić kontur glebowy do analizy za pomocą rozszerzenia Analiza geotechniczna. Ten dodatek można aktywować w danych bazowych modelu, jak pokazano na rysunku 01.