The structural analysis software RFEM 6 is the basis of a modular software system. The main program RFEM 6 is used to define structures, materials, and loads of planar and spatial structural systems consisting of plates, walls, shells, and members. The program also allows you to create combined structures as well as to model solid and contact elements.
RSTAB 9 is a powerful analysis and design software for 3D beam, frame, or truss structure calculations, reflecting the current state of the art and helping structural engineers meet requirements in modern civil engineering.
Do you often spend too long calculating cross-sections? Dlubal Software and the RSECTION stand-alone program facilitate your work by determining section properties of various cross-sections and performing a subsequent stress analysis.
Do you always know where the wind is blowing from? From the direction of innovation, of course! With RWIND 2, you have a program at your side that uses a digital wind tunnel for the numerical simulation of wind flows. The program simulates these flows around any building geometry and determines the wind loads on the surfaces.
Are you looking for an overview of snow load zones, wind zones, and seismic zones? Then you are in the right place. Use the Geo-Zone Tool to determine quickly and efficiently snow loads, wind speeds, and seismic data according to ASCE 7‑16 and other international standards.
Would you like to try out the capabilities of the Dlubal Software programs? You have the opportunity to do so! The free 90-day full version allows you to thoroughly test all our programs.
This webinar will provide an introduction to steel connection design acc. to the AISC 360-22 in RFEM 6.
This webinar will provide an introduction to steel member design acc. to the AISC 360-22 and 341-22 in RFEM 6.
In this webinar, you will learn how to calculate masonry structures in RFEM 6 using an FE analysis.
Free Webinar | RWIND 2 - Calculating Wind Loads with CFD Simulation (USA)
This webinar will provide an overview of calculating wind loads using CFD simulation with RWIND 2 and RFEM 6.
In this webinar, you will learn how to design a tent hall consisting of aluminum cross-sections in RFEM 6.
In this webinar, we show you how to model walls made of masonry in RFEM 6 and how to design them using the Finite Element Analysis (FEA).
Free Webinar | AISI S100 / CSA S136 Cold-Formed Steel Design in RFEM 6 (USA)
This webinar will provide an introduction to cold-formed steel member design acc. to the AISI S100 / CSA S136 in RFEM 6.
Free Webinar | AISC 360-16 Steel Connection Design in RFEM 6 (USA)
This webinar will provide an introduction to steel connection design using FEA acc. to the AISC 360-16 in RFEM 6.
Free Webinar | 2018 NDS CLT Design in RFEM 6 (USA)
This webinar will provide an introduction to cross-laminated timber (CLT) design acc. to the 2018 NDS in RFEM 6.
Free Webinar | Steel Silo Design in RFEM 6 (USA)
This webinar will provide an introduction to steel silo design in RFEM 6.
Free Webinar | Reinforced Concrete Tank Design in RFEM 6 (USA)
This webinar will provide an introduction to reinforced concrete tank analysis and design in RFEM 6.
Free Webinar | Construction Stages Analysis in RFEM 6 (USA)
This webinar will provide an introduction to construction stage analysis and design in RFEM 6.
This webinar provides an introduction to aluminum modeling and design in RFEM 6 and RSTAB 9.
This webinar provides an introduction to the design of aluminum structures in RFEM 6 and RSTAB 9.
Webinars provide the opportunity to gain expert knowledge and to ensure you’re getting the most out of your Dlubal programs.
Free Webinar | CFD Wind Simulation with RWIND 2 (USA)
This webinar will provide an introduction to CFD wind analysis utilizing RWIND 2 and RFEM 6.
Free Webinar | ADM 2020 Aluminum Design in RFEM 6 (USA)
This webinar will provide an introduction to aluminum member design acc. to the ADM 2020 in RFEM 6.
Free Webinar | ASCE 7-16 Response Spectrum Analysis in RFEM 6 (USA)
This webinar will provide an introduction to a response spectrum analysis acc. to the ASCE 7-16 in RFEM 6.
In this webinar, we will show you how to model and design aluminum structures in the structural analysis programs RFEM 6 and RSTAB 9.
This webinar shows you how to model and design an aluminum structure in RFEM 6 and RSTAB 9.
Dlubal webinars provide you with the opportunity to gain expert knowledge and to ensure you are getting the most out of your Dlubal Software programs.
In this webinar, we will show you how to design masonry in RFEM 6 using the finite element method.
Free Webinar | Tensile Membrane Structure Design in RFEM 6 (USA)
This webinar will provide an introduction to tensile membrane structure design in RFEM 6.
Free Webinar | NDS 2018 Timber Member Design in RFEM 6 (USA)
This webinar will provide an introduction to timber member design acc. to the NDS 2018 in RFEM 6.
Free Webinar | AISC 360-16 Steel Design in RFEM 6 (USA)
This webinar will provide an introduction to steel design acc. to the AISC 360-16 in RFEM 6.
This webinar will provide an introduction to the new generation FEA software RFEM 6.
This webinar demonstrates steel member design workflow according to the CSA S16:19 in RFEM.
This webinar demonstrates the aluminum member design workflow according to the Aluminum Design Manual (ADM) 2020 in RFEM.
Free webinar on the FEM structural analysis program RFEM | Soil-structure interaction in RFEM
In this webinar, we show you various options for using soil models in RFEM.