50 Results
View Results:
Sort by:
Implementation of Experimental Wind Tunnel Data in RFEM
How we can introduce experimental wind tunnel data in RFEM?
Implementation of Experimental Wind Tunnel Data in RWIND
How we can introduce experimental data in RWIND?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM
Temporary Structures
I would like to analyze temporary structures. Which programs do you recommend?
Power Plants and Conveyor Structures
Which programs can I use to design power plants and conveyor structures?
- 005437
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Steel Joints for RFEM 6
- Torsional Warping (7 DOF) for RFEM 6
- Torsional Warping (7 DOF) for RSTAB 9
- Steel Structures
- Structural Analysis & Design
- Stress Analysis
- Stability Analysis
- Warping Torsion Analysis
- Steel Connections
- Cold-Formed Sections
- Eurocode 3
- ANSI/AISC 360
- CSA S16
- IS 800
- GB 50017
- SP 63.13330
- BS 5950-1
- AS 4100
- SIA 263
Programs for Steel Structures
Which programs and add-ons are suitable for the structural analysis and design of steel structures?
AISC 341 Limit State Types
Which Limit State Types are applicable for the AISC 341 seismic design?
Standardized Sections for AISI Design
Which standardized sections are valid for AISI cold-formed steel design in RFEM 6?
Custom Sections for AISI Design
Can I design user-defined (parametric) sections according to AISI S100 or CSA S136?
AISI Table B4.1-1 Applicability Limits
Does RFEM check the applicability limits of AISI Table B4.1‑1?
Overstrength Factors
How do I include the overstrength factor(s) Ωo in the ASCE 7 load combinations?
Redundancy Factors
How do I include the redundancy factor(s) ρ in the ASCE 7 load combinations?
Creating Response Spectrum ASCE 7-22
How can I create a response spectrum according to ASCE 7‑22?
Mode Shapes - Limiting Selection of Shapes
I need many mode shapes to achieve a sum of 90% effective modal mass. Can I limit the number of mode shapes for generating equivalent loads?
National Annex DIN EN 1998-1/NA:2021-07
Is the German National Annex 2021‑07 to Eurocode 8 available in RFEM 5 / RSTAB 8?
Load Transfer Surface RWIND
Is it possible to use load transfer surfaces in RFEM 6 for wind load generation using RWIND?
Question
RF‑/DYNAM Pro – Forced Vibrations and RF‑/DYNAM Pro – Equivalent Loads perform the multi-modal response spectrum analysis. What are the differences?
Question
What method is applied in the RF‑/DYNAM Pro - Equivalent Loads add-on module?
Question
I have used the RF‑/DYNAM Pro add-on module to generate the governing result combinations of seismic loads. What is the next procedure to perform the design of the individual structural components?
Question
What should be considered when using a failure of columns under tension in the RF‑/DYNAM Pro – Equivalent Loads add-on module?
Question
I would like to perform seismic design of an irregular structure. Does RFEM automatically carry out the modal analysis (consideration of multiple vibration modes) on the spatial system, or do I have to use special settings for this?
Geo-zone tool
I noticed deviations from the map of DIN EN 1998‑1 or DIN 4149 in the online service "Geo-Zone Tool: Snow Load, Wind Speed, and Seismic Load Maps". Can you tell me which map is current and thus governing?
Question
How do you distinguish between the response spectrum with equivalent loads method and the response spectrum without equivalent loads method in RFEM and RSTAB?
Question
Why can I only calculate seismic loads in one direction when using RF‑/DYNAM Pro?
- 004727
- RFEM 5
- RSTAB 8
-
- Concrete Structures
- Steel Structures
- Timber Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Finite Element Analysis
- Wind Simulation & Wind Load Generation
- Stability Analysis
- Dynamic and Seismic Analysis
- Form-Finding and Cutting Patterns
- Cold-Formed Sections
- Eurocode 1
- Eurocode 3
- Eurocode 5