W dostępnych normach, takich jak EN 1991-1-4 [1], ASCE/SEI 7-16 i NBC 2015, przedstawiono parametry obciążenia wiatrem, takie jak współczynnik parcia wiatru (Cp ) dla podstawowe kształty. Ważne jest, jak szybciej i dokładniej obliczać parametry obciążenia wiatrem, niż pracować na czasochłonnych i czasami skomplikowanych wzorach w normach.
Przykład obliczeniowy opisuje obciążenia wiatrem działające na model grupy budynków w kilku kierunkach. The model consists of eight cubes. The velocity fields obtained by the RWIND simulation are compared with the measured values from the experiment. The experimental data are measured using a thermistor anemometer in the wind tunnel.
Przykład obliczeniowy opisuje obciążenia od ściskania ścian budynków w układzie tandem, zlokalizowanych w poziomie terenu. The buildings are simplified to rectangular objects and scaled down while maintaining the elevation ratios. The pressure distribution on the walls of the model of a medium-high building was conducted by an experiment. The chosen results (pressure coefficient Cp) are compared with the measured values.
Przykład obliczeniowy opisuje stacjonarny przepływ wokół wieżowca w postaci bloków miejskich (model w skali). The example is given by the Architectural Institute of Japan (AIJ). The chosen results (velocity magnitude) are compared with the measured values.
Przykład obliczeniowy opisuje stacjonarny przepływ wokół izolowanego budynku (model w skali). The chosen results (velocity magnitude) are compared with the measured values.
A sphere is subjected to a uniform flow of viscous fluid. The velocity of the fluid is considered at infinity. The goal is to determine the drag force. The parameters of the problem are set so that the Reynolds number is small and the radius of the sphere is also small, thus the theoretical solution can be reached - Stokes flow (G. G. Stokes 1851).
Naczynie grubościenne jest obciążone takim ciśnieniem wewnętrznym, że osiąga stan sprężysto-plastyczny. While neglecting self‑weight, the analytical and numerical solutions for the radial position of the plastic zone border (under the Tresca hypothesis) are determined and compared.
Ściana murowana jest poddana rozłożonemu obciążeniu w środku swojego górnego przekroju. The Isotropic Masonry 2D material model is compared with the Isotropic Linear Elastic model, with surface stiffness property Without Tension in the nonlinear calculation.
Wspornik jest obciążony siłą poprzeczną i osiową na prawym końcu i jest w pełni zamocowany na lewym końcu. The problem is described by the following set of parameters. The problem is solved by using the geometrically linear analysis, second-order analysis, and large deformation analysis.
Długa, cienka belka przenosi masę skupioną i jest obciążona siłą zależną od czasu. It is simply supported. The problem is described using the following parameters. Determine the deflections in the given test times.
Analiza czasowa belki wspornikowej (układ SDOF) wzbudzanej przez funkcję okresową. Vertical deformations and accelerations calculated with direct integration and modal analysis in RF‑/DYNAM Pro - Forced Vibrations are compared with the analytical solution.
Drewniana belka wzmocniona dwiema stalowymi płytami na końcach jest obciążona ściskaniem. The wood fibers are parallel to the upper loaded side of the beam. The plastic surface is described according to the Tsai-Wu plasticity theory.
Zostanie zdefiniowana belka wspornikowa o przekroju dwuteowym o długości L. The beam has five mass points with masses m acting in the X-direction. The self-weight is neglected. The frequencies, mode shapes, and equivalent loads of this 5-DOF system are analytically calculated and compared with the results from RSTAB and RFEM.
Należy określić maksymalne ugięcie czterech słupów zamocowanych u dołu i połączonych sztywnym blokiem u góry. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled as orthotropic elastic material, and the inner columns as orthotropic elastic-plastic material with the same elastic parameters as the outer columns and plasticity properties defined according to the Tsai-Wu plasticity theory.
Drewniana belka wzmocniona dwiema stalowymi płytami na końcach jest obciążona ściskaniem. The wood fibers are parallel to the upper loaded side of the beam. The plastic surface is described according to the Tsai-Wu plasticity theory.