In addition to our technical support (e.g. via chat), you’ll find resources on our website that may help you with your design using Dlubal Software.
Frequently Asked Questions (FAQ)
Customer Support 24/7
AnswerPlease decrease the maximum distance between the node and the line in the FE network settings. Even with a setting of 0.001 m corresponding to the image, a smaller value can be entered. If the decimal places are adjusted via the corresponding settings, the value is also displayed completely.
AnswerYou find this setting in the program options in the "Program" tab.If you exclude the check box "Description of combinations according to action category", the load case numbers are displayed in the COs.
Depending on the selected load determination type, RF-PUNCH Pro determines the punching load from the shear forces in the critical control perimeter. The internal forces in surfaces from the RFEM model are used here.
If the FE mesh in the area of the punching node is not fine enough, the results may be inaccurate. In this case, you get message no. 56.
To avoid the problem, you should perform an FE mesh refinement in the RFEM model in the area of the punching node . You can arrange them either directly on the node or on the connecting lines of the wall ends or wall corners.
If the FE mesh refinement is sufficiently fine, the warning message disappears automatically after a recalculation in RF-PUNCH Pro.
The program interprets the entered model for the calculation in a FE mesh. This mesh depends on the shape parameters set in the "FE Mesh" dialog box.
In order to correct any inaccuracies in the model, there is the parameter ε in the FE mesh settings. In the figurative sense, it regulates the maximum distance between the FE nodes. If the distance between the elements / nodes in the model is smaller than the parameter ε, the FE nodes are merged. The result of this merging is then the described "connection" of the members in the calculation.
You can avoid this effect and simulate the members independently by setting the parameter ε smaller than the available distance.
For the stability design of compression elements, you need the combination of RF-CONCRETE Members and RF-CONCRETE NL. The reason is the following:
First, the internal forces of the individual load combinations (second-order analysis + imperfection) are subjected to the linear-elastic calculation. For this, you basically only need RFEM.
Then, the cross-section design is performed in RF-CONCRETE Members with these internal forces determined linearly-elastically, and the required bending reinforcement is determined from these internal forces.
This bending reinforcement is then compared with the user-defined entries concerning the existing basic reinforcement or the minimum reinforcement and based on this, the reinforcement concept is generated (dialog box "3.1 Existing Longitudinal Reinforcement" of the module).
This existing longitudinal reinforcement is then used for the nonlinear design.
According to Section 5.8.6 (1), geometric nonlinearities must be taken into account according to the second-order analysis. However, the general rules for nonlinear methods according to 5.7 also apply.
In Sec. 5.7(1), "an adequate non-linear behaviour for materials is assumed." According to 5.7(4)P, the use of material characteristics which represent the stiffness in a realistic way but take account of the uncertainties of failure shall be used when using non-linear analysis.
This requires the RF-CONCRETE NL add-on module. Thus, the geometric and material nonlinearities are considered and the requirements of EC 2 regarding the ultimate limit state design are fulfilled.
Similarly, this method is also available in RSTAB in the CONCRETE add-on module.
Yes, you can. It is possible to export the critical perimeter from RF‑PUNCH Pro as a line to the RFEM model. This is possible for all punching forms (supports, wall ends and wall corners). The corresponding button can be found in the result window 2.1 "Punching Shear Design" (see figure).
In the RFEM model, you will then get a line, where you can create a "section" for further analyses, for example. Please note that the line must be integrated into the FE mesh of the surface. The setting for this can be found in the general FE mesh settings.
Unfortunately, there is no "Divide surface along selected line" function. You can divide the surface equally or along all integrated lines.
In order to divide the surface on only one integrated line, it is recommended to temporarily manage the integrated lines manually (see Figure 01). After splitting, the automatic object detection can be reactivated (see Figure 02).
AnswerIf you perform a punching shear design for a wall corner or a wall end at a floor slab or foundation plate, this entry is not necessary.Since the punching load is determined at a wall corner or a wall end from the shear forces in the control perimeter when performing the punching shear design, the ratio of the surface load is missing anyway within the control perimeter (up to the load application). Therefore, this entry is also not necessary in the 1.5 dialog box.If you, however, perform the punching shear design for a single column at a foundation plate with the punching load from the normal force of this column, you can enter the "Deductible Surface Load" at the end of the dialog box "1.5 Nodes of Punching Shear - Node of Punching Shear - Details" which allows to determine ΔVEd.
AnswerYou find this setting in the "General Data" of the model.You can distinguish between the model types "3D", "2D - XY", "2D - XZ" and "2D - XY".If you want to enter a floor as a 2D model, and the axial forces within the slab should not be taken into account, set the model type to "2D - XY". If you want to enter a wall, set "2D - XZ".Find more information in the RFEM manual, chapter 12.2.1 General - Type of Model.
AnswerThe title block of the printout report is created using the authorization file, which was used in the initial installation of our programs.
A subsequent change in the authorization file does not necessarily change all report headers immediately.
For the changed title block to be created as default in the authorization file, the "old" one has to be removed first.
To do so, please delete the file "DlubalProtocolConfigNew.cfg" in the following (default) directory:
While deleting the file, our applications must be closed!
Did you find your question?
If not, contact us via our free e-mail, chat, or forum support, or send us your question via the online form.
Your support is by far the best
“Thank you very much for the useful information.
I would like to pay a compliment to your support team. I am always impressed how quickly and professionally the questions are answered. In the industry of structural analysis, I use several software including service contract, but your support is by far the best.”