47 Results
View Results:
Sort by:
Adjusting NDS and CSA O86 Factors for Consideration in the Timber Design Add-on
How can the NDS and CSA O86 factors be manually adjusted for consideration in the Timber Design add-on?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM
Temporary Structures
I would like to analyze temporary structures. Which programs do you recommend?
Scaffolding and Rack Structures
We are looking for a program for scaffolding and rack structures. Is Dlubal Software suitable for this?
Programs for Timber Structures
Which Dlubal Software programs can I use to calculate and design timber structures?
- 005437
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Steel Joints for RFEM 6
- Torsional Warping (7 DOF) for RFEM 6
- Torsional Warping (7 DOF) for RSTAB 9
- Steel Structures
- Structural Analysis & Design
- Stress Analysis
- Stability Analysis
- Warping Torsion Analysis
- Steel Connections
- Cold-Formed Sections
- Eurocode 3
- ANSI/AISC 360
- CSA S16
- IS 800
- GB 50017
- SP 63.13330
- BS 5950-1
- AS 4100
- SIA 263
Programs for Steel Structures
Which programs and add-ons are suitable for the structural analysis and design of steel structures?
AISC 341 Limit State Types
Which Limit State Types are applicable for the AISC 341 seismic design?
Equivalent Round Section Dimension
How is the dimension for an equivalent round section calculated in the Timber Design add-on?
Splice Connection
How do I create a splice connection in the Steel Joints add-on?
Standardized Sections for AISI Design
Which standardized sections are valid for AISI cold-formed steel design in RFEM 6?
Custom Sections for AISI Design
Can I design user-defined (parametric) sections according to AISI S100 or CSA S136?
AISI Table B4.1-1 Applicability Limits
Does RFEM check the applicability limits of AISI Table B4.1‑1?
AISC 360-16 Shear Plane in Thread Option
Can I exclude bolt threads from the shear planes according to AISC 360-16 in the Steel Joints Add-on?
Exclude Lateral Torsional Buckling Check
My beam has a continuous lateral support and therefore lateral torsional buckling (LTB) is not a concern. How do I define the effective length?
Orthotropy Direction for Layers
Why cannot I define a rotation when defining layers?
Overstrength Factors
How do I include the overstrength factor(s) Ωo in the ASCE 7 load combinations?
Redundancy Factors
How do I include the redundancy factor(s) ρ in the ASCE 7 load combinations?
Effective Lengths for Steel Stability Design
How do I define effective lengths when designing steel members in RFEM 6?
Where can I activate the reduction of load combinations in RFEM 6? And how does this reduction work?
Where can I activate the reduction of load combinations in RFEM 6? And how does this reduction work?
Question
The online service "Snow Load, Wind Speed, and Seismic Load Maps" displays the snow load zones 1*, 1a*, 2*, and 3* for Germany. Where are these snow load zones defined?
Question
RF‑STEEL AISC add-module shows non-designable results for general cross-sections because of shear buckling checks according to Chapter G. How do I solve this?
Stability Design in RF-STEEL AISC
Why are my steel members not being designed for stability in RF-STEEL AISC?
Question
I am performing a design in RF‑/STEEL AISC for result combinations from RF‑/DYNAM Pro and get the error message "Not designable - Null value of the critical moment on the segment". What should I do?
- 004727
- RFEM 5
- RSTAB 8
-
- Concrete Structures
- Steel Structures
- Timber Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Finite Element Analysis
- Wind Simulation & Wind Load Generation
- Stability Analysis
- Dynamic and Seismic Analysis
- Form-Finding and Cutting Patterns
- Cold-Formed Sections
- Eurocode 1
- Eurocode 3
- Eurocode 5