27 Results
View Results:
Sort by:
Cutting and Editing Plates when Modeling Steel Joints
Why is it not possible to select the plate I want to cut/edit in the Plate Editor / Plate Cut?
Structure Below Ground Level
Why does the integration/support of my building in the ground below the ground level not work?
Setting of I-Beam Flange Support for Design in Structure Stability Add-on
In the Steel Design add-on, I have set the boundary conditions in such a way that the I-beam flange is restrained against the horizontal displacement. I then calculated the critical load factors using the Structure Stability add-on, but with no effect on the critical load factor value. What is the reason for this?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM
Temporary Structures
I would like to analyze temporary structures. Which programs do you recommend?
Tensile Membrane Structures
Which Dlubal programs do I need for tensile membrane structures?
Aluminum and Lightweight Structures
I would like to design an aluminum structure. Is it possible to use RFEM or RSTAB for this?
Cable and Tensile Structures
I would like to analyze cable and tensile structures. Is it possible to use RFEM or RSTAB for this?
Stability Analysis with Incrementally Increasing Loading
Can I incrementally increase the load in RFEM 6 or RSTAB 9?
Setting Deformations to 0
How can I set the deformations from an LC/CO or a construction stage to 0?
Geotechnical Analysis and Load Cases
I want to consider the soil-structure interaction using one of the nonlinear soil material models. Why is it not reasonable to calculate the individual load cases with this model?
Instability
My model is unstable. What could be the reason?
Exclude Lateral Torsional Buckling Check
My beam has a continuous lateral support and therefore lateral torsional buckling (LTB) is not a concern. How do I define the effective length?
Creating User-Defined Fabric
How do I create a user-defined fabric?
Creating Response Spectrum ASCE 7-22
How can I create a response spectrum according to ASCE 7‑22?
Strength of Weld-Affected Zone for Aluminum
How do I consider the strength of weld-affected zone for aluminum?
Small Cohesion for Non-Cohesive Soils
What value can I use for cohesion in order to avoid singularities?
Uneven Terrain
The terrain surface of my soil to be analyzed is uneven. How can I edit the geometry of my soil massif for the modeling?
Activating Geotechnical Analysis Add-on
I have a license for the Geotechnical Analysis add-on and it appears as available to me. However, I cannot activate it. What could be the reason?
Member Design Supports for Deflection Checks
How do I define a member as a cantilever and not as supported at both ends for serviceability or deflection design?
Instability
My model is unstable. What could be the reason?
Unstable Model - Troubleshooting
My model in RFEM 6 / RSTAB 9 is unstable. How can I fix it?
Export of Response Spectrum
Can I export a response spectrum from RFEM 6 and use it in RFEM 5, for example?
Neglecting Masses in RFEM 6 / RSTAB 9
How can I neglect masses in my modal analysis in RFEM 6 / RSTAB 9?
Response Spectrum Analysis
How can I perform an earthquake analysis in RFEM 6 and RSTAB 9?
- 005113
- Timber Design for RFEM 6
- Timber Design for RSTAB 9
-
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Stress-Strain Analysis for RFEM 6
- Stress-Strain Analysis for RSTAB 9
- Steel Joints for RFEM 6
- Timber Structures
- Concrete Structures
- Steel Structures
- Structural Analysis & Design
- Eurocode 2
- Eurocode 3
- Eurocode 5
- Eurocode 9