Niniejszy artykuł skupia się na specyficznych aspektach projektowania konstrukcji membranowych, które mają specyficzne wymagania, takich jak znajdowanie kształtu (form-finding) i generowanie szablonów cięcia. Integralną częścią projektowania tych konstrukcji jest proces wyszukiwania odpowiednich wstępnie sprężonych kształtów i generowania szablonów cięcia. Tekst krótko opisuje dwa podstawowe procesy w projektowaniu konstrukcji membranowych. Celem jest zilustrowanie ich fizycznego charakteru i zademonstrowanie poszczególnych stwierdzeń za pomocą towarzyszących im przykładów.
Rozszerzenie Analiza geotechniczna zapewnia programowi RFEM dodatkowe specyficzne modele materiałowe podłoża, które mogą odpowiednio odwzorować złożone zachowanie materiału podłoża. W tym artykule zaprezentujemy, w jaki sposób można określić zależną od naprężeń sztywność modeli materiałowych gruntu.
W programie RFEM 6 możliwe jest definiowanie wielowarstwowych konstrukcji powierzchniowych za pomocą rozszerzenia „Powierzchnie wielowarstwowe”. Jeżeli zatem rozszerzenie zostało aktywowane w Danych ogólnych modelu, możliwe jest definiowanie konstrukcji warstwowych dla dowolnego modelu materiału. Możliwe jest również łączenie modeli materiałowych, na przykład materiałów izotropowych i ortotropowych.
Das Einfügen von Löchern in Flächen ist durch eine große Auswahl an Werkzeugen sehr einfach. Um bei Volumen Löcher oder Bohren einzufügen, ist zu beachten, dass bei einem durchgehendem Loch am Anfang und am Ende eine Öffnung erstellt werden muss und zudem eine Fläche, welche das Loch von dem Volumen abtrennt.
Mit dem nichtlinear-elastischen Materialmodell können in RFEM 5 Flächen und Volumen mit nichtlinearen Materialeigenschaften berechnet und eine Spannungsauswertung durchgeführt werden.
Deformacje sprężyste elementu konstrukcyjnego pod wpływem obciążenia są oparte na prawie Hooke'a, opisującym liniową zależność naprężenie-odkształcenie. Są one odwracalne: po odciążeniu element powraca do swojego pierwotnego kształtu. Jednakże deformacje plastyczne są nieodwracalne i zazwyczaj znacznie większe niż odkształcenia sprężyste. W przypadku naprężeń plastycznych materiałów ciągliwych, takich jak stal, efekty plastyczności występują w miejscach, w których wzrostowi odkształceń towarzyszy zjawisko lokalnego wzmocnienia. Prowadzi to do powstania trwałych deformacji, a w ekstremalnych przypadkach do zniszczenia elementu konstrukcyjnego.
Podczas analizy sił podporowych dla linii, uzyskane wykresy czasem na pierwszy rzut oka wydają się nieprawdopodobne. W szczególności: w przypadku obciążeń zmiennych w miejscach, w których również znajdują się podpory węzłowe, w punktach podziału i na krawędziach linii podpartych wyniki czasami pokazują nieoczekiwane reakcje podporowe. Włączenie funkcji liniowego rozkładu gładkiego w Nawigatorze projektu - Wyświetlanie nie zawsze pokazuje spodziewany wykres wyników.
Bei der Abbildung einer Rippe aus Stahlbeton mit darüberstehender Mauerwerkswand besteht die Gefahr einer Unterbemessung der Rippe, wenn das Tragverhalten des Mauerwerks nicht korrekt berücksichtigt und die Verbindung zwischen Mauerwerkswand und Unterzug nicht ausreichend genau modelliert wird. Dieser Artikel soll sich mit dieser Problematik und den möglichen Modellierungen einer solchen Konstruktion auseinandersetzen. Im Beispiel wird die Bewehrung rein aus den Schnittgrößen und ohne jegliche konstruktive Mindestbewehrung ermittelt.
Bemessen werden soll ein Montagestoß aus Hohlprofilen mit Stirnplatten. Es handelt sich hierbei um den Untergurt eines Fachwerkträgers, welcher aus Transportgründen geteilt werden muss.
Ortotropowe prawa materiałowe są stosowane wszędzie tam, gdzie materiały są uporządkowane zgodnie z ich obciążeniem. Przykłady obejmują tworzywa sztuczne wzmocnione włóknami, blachy trapezowe, beton zbrojony i drewno.
Zwłaszcza w przypadku, gdy wymagane jest przeprowadzenie analizy sąsiedniego obszaru punktów połączenia, geometria lub obciążenie połączenia nie odpowiada normom lub jeśli konstrukcja wymaga analizy przy użyciu modelu MES (np. w inżynierii przemysłowej). jest konieczne do szczegółowej analizy połączeń w modelu ES.
Umocnienie odkształceniowe to zdolność materiału do osiągnięcia większej sztywności poprzez redystrybucję (rozciąganie) mikrokryształów w sieci krystalicznej konstrukcji. Rozróżnia się utwardzanie izotropowe materiału jako wartości skalarne lub tensoryczne utwardzanie kinematyczne.
Jeden z moich wcześniejszych artykułów opisał model materiałowy Izotropowy nieliniowo sprężysty. Viele Materialien besitzen aber kein rein symmetrisches nichtlineares Materialverhalten. Auch die in dem Beitrag erwähnten Fließgesetze nach von Mises, Drucker-Prager und Mohr-Coulomb sind in dieser Hinsicht auf die Fließfläche im Hauptspannungsraum beschränkt.
Poniższy przykład prezentuje porównanie modelu powłokowego i prostego modelu prętowego w programie RFEM. W przypadku modelu powłokowego belka jest podwieszona do powierzchni, która ze względu na warunki brzegowe jest po obu stronach modelowana z utwierdzeniami. Damit handelt es sich um ein statisch unbestimmtes System, welches bei einer Überlast Fließgelenke ausbildet. Der Vergleich wird hier mit einem Stabmodell geführt, welches dieselben Randbedingungen erhält wie das Schalenmodell.
Aby za pomocą programu RFEM oszacować zachowanie konstrukcyjne muru w sposób zbliżony do rzeczywistości, należy najpierw wybrać materiał i model materiałowy. Da Mauerwerk auf Zug mit Rissbildung reagiert, muss hier ein nichtlineares Materialmodell verwendet werden, welches bei Vorhandensein des Zusatzmoduls RF-MAT NL selektiert werden kann.