22 Wyniki
Wyświetl wyniki:
Sortuj według:
Utwórz spektrum odpowiedzi ASCE 7-22
Jak utworzyć spektrum odpowiedzi zgodnie z ASCE 7-22?
Metoda modułu sztywności
Czy możliwe jest przeprowadzenie analizy według metody modułu sztywności w programie RFEM lub RSTAB?
AISC 360-16 Płaszczyzna ścinania w gwincie
Czy mogę wykluczyć gwinty śrub z płaszczyzn ścinania zgodnie z AISC 360-16 w rozszerzeniu Połączenia stalowe?
Połączenie nakładkowe
Jak utworzyć połączenie typu splot w rozszerzeniu Steel Joints?
Nierówny teren
Powierzchnia mojego podłoża gruntowego, które ma zostać przeanalizowane, jest nierówna. Jak edytować geometrię masywu gruntowego w celu jego modelowania?
Analiza spektrum odpowiedzi
Jak mogę przeprowadzić analizę trzęsienia ziemi w RFEM 6 i RSTAB 9?
Eksport spektrum odpowiedzi
Czy mogę wyeksportować spektrum odpowiedzi z programu RFEM 6 i wykorzystać je na przykład w programie RFEM 5?
- 005113
- Projektowanie konstrukcji drewnianych RFEM 6
- Projektowanie konstrukcji drewnianych RSTAB 9
-
- Projektowanie konstrukcji aluminiowych RFEM 6
- Projektowanie konstrukcji aluminiowych RSTAB 9
- Projektowanie konstrukcji stalowych RFEM 6
- Projektowanie konstrukcji stalowych RSTAB 9
- Analiza naprężeniowo-odkształceniowa RFEM 6
- Analiza naprężeniowo-odkształceniowa RSTAB 9
- Połączenia stalowe RFEM 6
- Konstrukcje drewniane
- Konstrukcje betonowe
- Konstrukcje stalowe
- Analiza statyczno-wytrzymałościowa
- Eurocode 2
- Eurocode 3
- Eurocode 5
- Eurocode 9
Materiały załączników krajowych
Gdzie znajdę materiały do odpowiednich załączników krajowych w programie RFEM 6 i RSTAB 9?
Wymiarowanie w oparciu o przypadek z różnymi sytuacjami obciążenia
Jak przeprowadzić obliczenia w zależności od przypadku dla różnych sytuacji obciążeniowych?
Faza budowy - modyfikacja właściwości
Czy na poszczególnych etapach budowy można zmieniać właściwości prętów lub powierzchni, np. ich położenie?
Mała spójność dla gruntów niespoistych
Jakiej wartości mogę użyć dla spójności, aby uniknąć osobliwości?
Pomijanie mas w programie RFEM 6/RSTAB 9
Jak mogę pominąć masy w analizie modalnej w programie RFEM 6/RSTAB 9?
Ustawianie odkształceń na 0
Jak ustawić odkształcenia z PO/KO lub etapu budowy na 0?
Aktywacja rozszerzenia Analiza geotechniczna
Posiadam licencję na rozszerzenie Analiza geotechniczna i wydaje mi się, że jest dostępna. Nie można jednak aktywować rozszerzenia. Jaka może być tego przyczyna?
- 005437
- RFEM 6
- RSTAB 9
-
- Projektowanie konstrukcji stalowych RFEM 6
- Projektowanie konstrukcji stalowych RSTAB 9
- Połączenia stalowe RFEM 6
- Skręcanie skrępowane (7 stopni swobody) RFEM 6
- Skręcanie skrępowane (7 stopni swobody) RSTAB 9
- Konstrukcje stalowe
- Analiza statyczno-wytrzymałościowa
- Analiza naprężeń
- Sprawdzenie stateczności
- Analiza skręcania skrępowanego
- Połączenia stalowe
- Profile formowane na zimno
- Eurocode 3
- ANSI/AISC 360
- CSA S16
- IS 800
- GB 50017
- SP 63.13330
- BS 5950-1
- AS 4100
- SIA 263