60 Results
View Results:
Sort by:
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM
Temporary Structures
I would like to analyze temporary structures. Which programs do you recommend?
Power Plants and Conveyor Structures
Which programs can I use to design power plants and conveyor structures?
Aluminum and Lightweight Structures
I would like to design an aluminum structure. Is it possible to use RFEM or RSTAB for this?
Cable and Tensile Structures
I would like to analyze cable and tensile structures. Is it possible to use RFEM or RSTAB for this?
Standardized Sections for AISI Design
Which standardized sections are valid for AISI cold-formed steel design in RFEM 6?
Custom Sections for AISI Design
Can I design user-defined (parametric) sections according to AISI S100 or CSA S136?
AISI Table B4.1-1 Applicability Limits
Does RFEM check the applicability limits of AISI Table B4.1‑1?
Creating Response Spectrum ASCE 7-22
How can I create a response spectrum according to ASCE 7‑22?
Imperfection from Mode Shape
How do I create an imperfection based on a mode shape in RFEM 6?
Mode Shapes - Limiting Selection of Shapes
I need many mode shapes to achieve a sum of 90% effective modal mass. Can I limit the number of mode shapes for generating equivalent loads?
National Annex DIN EN 1998-1/NA:2021-07
Is the German National Annex 2021‑07 to Eurocode 8 available in RFEM 5 / RSTAB 8?
Question
RF‑/DYNAM Pro – Forced Vibrations and RF‑/DYNAM Pro – Equivalent Loads perform the multi-modal response spectrum analysis. What are the differences?
Question
What method is applied in the RF‑/DYNAM Pro - Equivalent Loads add-on module?
Question
I am trying to design an open, unsymmetric aluminum cross-section in RF‑/ALUMINUM and I am get the warning "Non-designable - 1022) General cross-section — Check of stability is not available". What is the reason?
Question
I have used the RF‑/DYNAM Pro add-on module to generate the governing result combinations of seismic loads. What is the next procedure to perform the design of the individual structural components?
Question
When performing the fire resistance design with TIMBER Pro, I get Error 10001. How can I fix the error?
Question
What should be considered when using a failure of columns under tension in the RF‑/DYNAM Pro – Equivalent Loads add-on module?
Question
Is it possible to design the support pressure or the compression perpendicular to the grain in RX‑TIMBER?
Question
After the design was performed using RF‑/TIMBER Pro, I optimized a cross-section. Why is the utilization of the optimized cross-section exceeded now?
Question
How can I create a drilled beam in RFEM?
Question
I would like to perform seismic design of an irregular structure. Does RFEM automatically carry out the modal analysis (consideration of multiple vibration modes) on the spatial system, or do I have to use special settings for this?
Geo-zone tool
I noticed deviations from the map of DIN EN 1998‑1 or DIN 4149 in the online service "Geo-Zone Tool: Snow Load, Wind Speed, and Seismic Load Maps". Can you tell me which map is current and thus governing?
Question
I have a question about the results of the serviceability limit state design: How is the increment of the dead load by the factor of 1.8 and the imposed load by 1.48 explained in the result combinations for the SLS design?
Question
How do you distinguish between the response spectrum with equivalent loads method and the response spectrum without equivalent loads method in RFEM and RSTAB?
Question
Where can I adjust the effective length lef according to Table 6.1 of Eurocode 5 in the TIMBER Pro add-on module?
Question
Why can I only calculate seismic loads in one direction when using RF‑/DYNAM Pro?
Question
I would like to design the connection of the diagonals of a truss with a steel lower flange and timber diagonals. Is this possible?
- 004727
- RFEM 5
- RSTAB 8
-
- Concrete Structures
- Steel Structures
- Timber Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Finite Element Analysis
- Wind Simulation & Wind Load Generation
- Stability Analysis
- Dynamic and Seismic Analysis
- Form-Finding and Cutting Patterns
- Cold-Formed Sections
- Eurocode 1
- Eurocode 3
- Eurocode 5