25 Results
View Results:
Sort by:
Question
What is the formula used to calculate the ASCE 7 wind velocity profile?
Question
Is the Gust-effect (G or Gf) from the ASCE 7‑16 Sect. 26.11 considered in RWIND Simulation?
ASCE 7 Seismic Load Combinations
I do not see the seismic load cases in my generated ASCE 7 load combinations (COs). How do I add them?
ASCE 7 Orthogonal Directional Combination Procedure
How do I apply the ASCE 7 Orthogonal Directional Combination procedure (100% + 30% rule) to my seismic load in a static analysis?
Question
I am designing a cross-section created in the SHAPE‑THIN program using the design add-on module, but the program shows the error message "ER006 Invalid type of c/t-part for cross-section of type General". What can I do?
Question
Is it possible to perform automatic live load reduction in RFEM or RSTAB per the ASCE, IBC, or NBCC?
Overstrength Factors
How do I include the overstrength factor(s) Ωo in the ASCE 7 load combinations?
Redundancy Factors
How do I include the redundancy factor(s) ρ in the ASCE 7 load combinations?
Exclude Lateral Torsional Buckling Check
My beam has a continuous lateral support and therefore lateral torsional buckling (LTB) is not a concern. How do I define the effective length?
Question
I need to define different types of lateral intermediate restrains for a single element in RF-/STEEL EC3. Is this possible?
ASCE 7 Reduced Live Load Factor
My live load is less than or equal to 100 psf. How do I consider the reduced load factor in the ASCE 7 load combinations?
AISI Table B4.1-1 Applicability Limits
Does RFEM check the applicability limits of AISI Table B4.1‑1?
Standardized Sections for AISI Design
Which standardized sections are valid for AISI cold-formed steel design in RFEM 6?
Question
In FOUNDATION Pro, I get extremely large foundations for my structure or I have to enter a very high loading in order to fulfill the design of the foundation torsion. What can be the reason?
Question
When designing seismic equivalent loads with a Response Spectra Analysis (RSA) in RFEM, how can I apply the modal response parameters Ie/R according to Sect. 12.9.1.2 in the ASCE‑7‑16 to my results?
- 005113
- Timber Design for RFEM 6
- Timber Design for RSTAB 9
-
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Stress-Strain Analysis for RFEM 6
- Stress-Strain Analysis for RSTAB 9
- Steel Joints for RFEM 6
- Timber Structures
- Concrete Structures
- Steel Structures
- Structural Analysis & Design
- Eurocode 2
- Eurocode 3
- Eurocode 5
- Eurocode 9
Materials of National Annexes
Where can I find the materials for the corresponding National Annexes in RFEM 6 and RSTAB 9?
Custom Sections for AISI Design
Can I design user-defined (parametric) sections according to AISI S100 or CSA S136?
Question
Is there a way to prepare an EC3 buckling check without setting the intermediate support manually, or is there a workaround that can speed this up?
Cable and Tensile Structures
I would like to analyze cable and tensile structures. Is it possible to use RFEM or RSTAB for this?
- 005437
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Steel Joints for RFEM 6
- Torsional Warping (7 DOF) for RFEM 6
- Torsional Warping (7 DOF) for RSTAB 9
- Steel Structures
- Structural Analysis & Design
- Stress Analysis
- Stability Analysis
- Warping Torsion Analysis
- Steel Connections
- Cold-Formed Sections
- Eurocode 3
- ANSI/AISC 360
- CSA S16
- IS 800
- GB 50017
- SP 63.13330
- BS 5950-1
- AS 4100
- SIA 263
Programs for Steel Structures
Which programs and add-ons are suitable for the structural analysis and design of steel structures?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM