111 Results
View Results:
Sort by:
- 005437
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Steel Joints for RFEM 6
- Torsional Warping (7 DOF) for RFEM 6
- Torsional Warping (7 DOF) for RSTAB 9
- Steel Structures
- Structural Analysis & Design
- Stress Analysis
- Stability Analysis
- Warping Torsion Analysis
- Steel Connections
- Cold-Formed Sections
- Eurocode 3
- ANSI/AISC 360
- CSA S16
- IS 800
- GB 50017
- SP 63.13330
- BS 5950-1
- AS 4100
- SIA 263
Programs for Steel Structures
Which programs and add-ons are suitable for the structural analysis and design of steel structures?
CSA S16 Class 4 Sections
Can I design members with Class 4 sections according to CSA S16 in the Steel Design add-on?
Line Hinges on Several Surfaces
How can I efficiently define line hinges on several surfaces?
Why are new COs generated during the calculation in RF‑/FOUNDATION Pro?
Why are new COs generated during the calculation in RF‑/FOUNDATION Pro?
Where can I activate the reduction of load combinations in RFEM 6? And how does this reduction work?
Where can I activate the reduction of load combinations in RFEM 6? And how does this reduction work?
Favorable Permanent Actions
Where can I activate the "Favorable permanent actions" option in RFEM 6 and RSTAB 9 in order to combine the self-weight in the ultimate limit state with 1.0?
Load Transfer Surface RWIND
Is it possible to use load transfer surfaces in RFEM 6 for wind load generation using RWIND?
Combinations for Road Bridges According to EN 1991-2 in RFEM 6
Does RFEM 6 include the combinations for road bridges according to EN 1991‑2?
Opening RWIND in RFEM 6 or RSTAB 9
How can I open RWIND using the load wizard in RFEM and RSTAB?
Question
For the settlement calculation in the RF‑SOILIN add-on module, the specific weight gamma and gamma,sat are required for the soil. What do I need the value gamma,sat for, and how is it assumed in the calculation?
Question
Does the program check the lap length of the vertical stirrups of a block foundation with smooth bucket sides?
Question
The online service "Snow Load, Wind Speed, and Seismic Load Maps" displays the snow load zones 1*, 1a*, 2*, and 3* for Germany. Where are these snow load zones defined?
Question
I have used the RF‑/DYNAM Pro add-on module to generate the governing result combinations of seismic loads. What is the next procedure to perform the design of the individual structural components?
Bending Design of Block Foundations
How is the static depth d calculated in the bending design of block foundations (calculation as equivalent beams)?
CSA S16 Class 4 Section
My section is classified as Class 4 and non-designable in RF-/STEEL CSA. However, my manual calculation shows a different class. Why the difference?
Imposed Loads with Stiffness Modifications
I have defined temperature loads, strain loads, or a precamber. Once I modify stiffnesses, the deformations are no longer plausible.
Question
How can I apply wind load distribution to a cylinder according to EN 1991‑4, Section 7.9?
Question
I design timber components. The deformations of the load combinations deviate from the manual calculation by exactly the coefficient of the material partial safety factor. Why?
Question
I noticed deviations from my sources in the online service "Snow Load, Wind Speed, and Seismic Load Maps". Where can I find information about the sources of your online service?
Geo-zone tool
I noticed deviations from the map of DIN EN 1998‑1 or DIN 4149 in the online service "Geo-Zone Tool: Snow Load, Wind Speed, and Seismic Load Maps". Can you tell me which map is current and thus governing?
- 004727
- RFEM 5
- RSTAB 8
-
- Concrete Structures
- Steel Structures
- Timber Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Finite Element Analysis
- Wind Simulation & Wind Load Generation
- Stability Analysis
- Dynamic and Seismic Analysis
- Form-Finding and Cutting Patterns
- Cold-Formed Sections
- Eurocode 1
- Eurocode 3
- Eurocode 5