46 Wyniki
Wyświetl wyniki:
Sortuj według:
Pytanie
Dlaczego nie jest możliwe obliczenie zginania dwuosiowego za pomocą modułu dodatkowego RF-/JOINTS?
Połączenia drewniane zgodnie z EN 1995-1-1, rozdział 8.2.2
Czy można użyć modułu dodatkowego JOINTS do wymiarowania połączeń drewno-drewno zgodnie z EN 1995-1-1, rozdział 8.2.2 w programach RFEM 5 i RSTAB 8?
Pytanie
W programie TIMBER Pro nie umiem obliczać prętów o podwójnych przekrojach prostokątnych i zmiennej liniowo wysokości przekroju. Jaki jest powód?
Pytanie
Dlaczego wyniki prętów i zbiorów prętów różnią się w obliczeniach?
Pytanie
W jaki sposób mogę wygenerować stężenie lub sprężystość dla podpory w RX-TIMBER Glued-Laminated Beam?
Ustawienie języka dla RX-TIMBER
Jak mogę zmienić język w module dodatkowym RX‑TIMBER?
Pytanie
W pośrednich wynikach programu RF‑SOILIN wartości wyświetlane są w kolorze czerwonym. Dlaczego?
Pytanie
Jak określić środek sztywności mojego układu konstrukcyjnego?
Pytanie
W module dodatkowym RF-/JOINTS Timber - Steel to Timber znajduje się informacja, że długość pręta jest za mała. Jaka jest minimalna długość i jak uniknąć problemu?
Sprężysty moment krytyczny zwichrzenia
Jakie są możliwości programu RFEM 5 lub RSTAB 8, aby określić sprężysty moment krytyczny zwichrzenia dowolnych przekrojów, układów lub obciążeń? Czy możliwe jest zaprojektowanie płaskiej konstrukcji stalowej (wsporniki, stalowe podłużnice schodów)?
Pytanie
Jakie kombinacje wyników mogę wymiarować w programie RF-/JOINTS Pro i na co należy zwrócić uwagę?
Pytanie
Czy w module dodatkowym RF‑FOUNDATION Pro mogę obrócić fundament wokół osi Z?
Pytanie
Czy możliwe jest zaimportowanie długości efektywnych z RF-/TIMBER Pro z RF ‑ STABILITY lub RSBUCK?
Pytanie
Co się stanie, jeżeli aktywuję funkcję "Zakłócenie gruntu" w RF‑SOILIN?
Pytanie
Czy RF-TIMBER AWC może optymalizować przekroje pod kątem obliczeń z uwagi na warunki pożarowe?
Pytanie
Jak mogę zmienić współczynnik korekcyjny ścinania kcr w RF‑JOINTS Timber to Timber?
Pytanie
Ile prętów można połączyć z węzłem w RF-/JOINTS Timber - Steel to Timber i jaki jest minimalny kąt między prętami?
Pytanie
Czy w module dodatkowym RF-/JOINTS Timber - Steel to Timber można automatycznie uwzględniać sztywność elementów złącznych podczas określania sił wewnętrznych?
- 004727
- RFEM 5
- RSTAB 8
-
- Konstrukcje betonowe
- Konstrukcje stalowe
- Konstrukcje drewniane
- Rozciągane konstrukcje membranowe
- Analiza statyczno-wytrzymałościowa
- Analiza metodą elementów skończonych
- Symulacja przepływu wiatru i generowanie obciążenia wiatrem
- Sprawdzenie stateczności
- Analiza dynamiczna i sejsmiczna
- Form-Finding i szablony cięcia
- Profile formowane na zimno
- Eurocode 1
- Eurocode 3
- Eurocode 5