48 Wyniki
Wyświetl wyniki:
Sortuj według:
- 005450
- RFEM 6
- RSTAB 9
-
- Projektowanie konstrukcji stalowych RFEM 6
- Projektowanie konstrukcji stalowych RSTAB 9
- Projektowanie konstrukcji aluminiowych RFEM 6
- Projektowanie konstrukcji aluminiowych RSTAB 9
- Form-Finding RFEM 6
- Konstrukcje stalowe
- Lekkie konstrukcje aluminiowe
- Konstrukcje tymczasowe
- Rozciągane konstrukcje membranowe
- Analiza statyczno-wytrzymałościowa
- Form-Finding i szablony cięcia
- Analiza dynamiczna i sejsmiczna
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM
Konstrukcje tymczasowe
Chciałbym przeprowadzić analizę konstrukcji tymczasowych. Jakie programy polecacie?
Rozciągane konstrukcje membranowe
Jakich programów firmy Dlubal potrzebuję do pracy z konstrukcjami membranowymi i membranowymi?
- 005443
- RFEM 6
- RSTAB 9
-
- Form-Finding RFEM 6
- Projektowanie konstrukcji aluminiowych RFEM 6
- Projektowanie konstrukcji aluminiowych RSTAB 9
- Konstrukcje stalowe
- Rozciągane konstrukcje membranowe
- Lekkie konstrukcje aluminiowe
- Analiza statyczno-wytrzymałościowa
- Symulacja przepływu wiatru i generowanie obciążenia wiatrem
- Form-Finding i szablony cięcia
- Eurocode 3
- Eurocode 9
Konstrukcje kablowe i poddawane rozciąganiu
Chciałbym przeprowadzić analizę konstrukcji kablowych i sieci kablowych. Czy można w tym celu wykorzystać program RFEM lub RSTAB?
Programy do konstrukcji drewnianych warstwowych i klejonych krzyżowo
Jakich programów potrzebuję do pracy z konstrukcjami warstwowymi lub drewnem klejonym krzyżowo (CLT)?
- 005437
- RFEM 6
- RSTAB 9
-
- Projektowanie konstrukcji stalowych RFEM 6
- Projektowanie konstrukcji stalowych RSTAB 9
- Połączenia stalowe RFEM 6
- Skręcanie skrępowane (7 stopni swobody) RFEM 6
- Skręcanie skrępowane (7 stopni swobody) RSTAB 9
- Konstrukcje stalowe
- Analiza statyczno-wytrzymałościowa
- Analiza naprężeń
- Sprawdzenie stateczności
- Analiza skręcania skrępowanego
- Połączenia stalowe
- Profile formowane na zimno
- Eurocode 3
- ANSI/AISC 360
- CSA S16
- IS 800
- GB 50017
- SP 63.13330
- BS 5950-1
- AS 4100
- SIA 263
Programy dla konstrukcji stalowych
Jakie programy i rozszerzenia są odpowiednie do obliczeń i wymiarowania konstrukcji stalowych?
Znormalizowane przekroje do obliczeń AISI
Które znormalizowane przekroje są ważne dla obliczeń elementów stalowych AISI formowanych na zimno w programie RFEM 6?
Profile niestandardowe dla AISI Design
Czy mogę zaprojektować przekroje zdefiniowane przez użytkownika (parametryczne) zgodnie z AISI S100 lub CSA S136?
AISI Tabela B4.1-1 Ograniczenia zastosowania
Czy program RFEM sprawdza granice stosowalności tabeli AISI B4.1-1?
AISC 360-16 Płaszczyzna ścinania w gwincie
Czy mogę wykluczyć gwinty śrub z płaszczyzn ścinania zgodnie z AISC 360-16 w rozszerzeniu Połączenia stalowe?
Przeguby liniowe na wielu powierzchniach
Jak skutecznie zdefiniować przeguby liniowe na wielu powierzchniach?
Nieprawdopodobne wyniki skręcania skrępowanego
Moje wyniki dla obliczeń ze skręcaniem skrępowanym są nieprawdopodobne. Jaka może być tego przyczyna?
Długości efektywne w obliczaniu stateczności konstrukcji stalowych
Jak zdefiniować długości efektywne podczas wymiarowania prętów stalowych w programie RFEM 6?
Info Day Online 2018
Czy modele i prezentacje z Info Day 2018 są ogólnie dostępne i czy możecie mi je przysłać?
RF -STEEL Surfaces - Naprężenia membranowe
Jak mogę wyświetlić naprężenia membranowe w wynikach RF ‑ STEEL Surfaces?
Pytanie
Jak mogę zoptymalizować czas obliczeń w CRANEWAY?
Pytanie
Moduł dodatkowy RF STEEL AISC wyświetla wyniki nieobliczalne dla przekrojów ogólnych ze względu na kontrolę wyboczenia zgodnie z rozdziałem G. Jak mogę to rozwiązać?
Analiza stateczności w RF-STEEL AISC
Dlaczego moje pręty stalowe nie są zaprojektowane pod kątem stateczności w RF-STEEL AISC?
Pytanie
Jak interpretowane są znaki dla wyników zwolnienia w przypadku zwolnienia liniowego i przegubów liniowych?
Momenty graniczne przy skręcaniu skrępowanym
Moduł RF-/STEEL Warping Torsion pozwala na wymiarowanie belki przyściennej modelowanej mimośrodowo, obciążonej poprzecznie obciążeniem rozłożonym. Podczas gdy momenty zginające w programie głównym wynoszą zero na początku i na końcu pręta ze względu na przeguby, RF-/STEEL Warping Torsion wyświetla momenty. W ten sposób moment w przęśle jest niepoprawnie redukowany. Jak ustawić momenty graniczne na zero?
- 004727
- RFEM 5
- RSTAB 8
-
- Konstrukcje betonowe
- Konstrukcje stalowe
- Konstrukcje drewniane
- Rozciągane konstrukcje membranowe
- Analiza statyczno-wytrzymałościowa
- Analiza metodą elementów skończonych
- Symulacja przepływu wiatru i generowanie obciążenia wiatrem
- Sprawdzenie stateczności
- Analiza dynamiczna i sejsmiczna
- Form-Finding i szablony cięcia
- Profile formowane na zimno
- Eurocode 1
- Eurocode 3
- Eurocode 5