21 Wyniki
Wyświetl wyniki:
Sortuj według:
Niestateczność
My model is unstable. Jaka może być przyczyna?
Niestateczność
Mój model jest niestateczny. Jaka może być przyczyna?
Pytanie
Jakie są współczynniki redukcji sztywności k33 i k88 w RF -LAMINATE?
Utwórz spektrum odpowiedzi ASCE 7-22
Jak utworzyć spektrum odpowiedzi zgodnie z ASCE 7-22?
Przegub liniowy połączenia płyta-ściana
Chciałbym połączyć moją ścianę murowaną z płytą żelbetową. Jaki jest najlepszy sposób na utworzenie przegubu liniowego?
AISC 360-16 Płaszczyzna ścinania w gwincie
Czy mogę wykluczyć gwinty śrub z płaszczyzn ścinania zgodnie z AISC 360-16 w rozszerzeniu Połączenia stalowe?
Połączenie nakładkowe
Jak utworzyć połączenie typu splot w rozszerzeniu Steel Joints?
Model niestabilny - rozwiązywanie problemów
Mein Modell in RFEM 6/ RSTAB 9 ist instabil. Jak mogę to naprawić?
Analiza spektrum odpowiedzi
Jak mogę przeprowadzić analizę trzęsienia ziemi w RFEM 6 i RSTAB 9?
Eksport spektrum odpowiedzi
Czy mogę wyeksportować spektrum odpowiedzi z programu RFEM 6 i wykorzystać je na przykład w programie RFEM 5?
- 005113
- Projektowanie konstrukcji drewnianych RFEM 6
- Projektowanie konstrukcji drewnianych RSTAB 9
-
- Projektowanie konstrukcji aluminiowych RFEM 6
- Projektowanie konstrukcji aluminiowych RSTAB 9
- Projektowanie konstrukcji stalowych RFEM 6
- Projektowanie konstrukcji stalowych RSTAB 9
- Analiza naprężeniowo-odkształceniowa RFEM 6
- Analiza naprężeniowo-odkształceniowa RSTAB 9
- Połączenia stalowe RFEM 6
- Konstrukcje drewniane
- Konstrukcje betonowe
- Konstrukcje stalowe
- Analiza statyczno-wytrzymałościowa
- Eurocode 2
- Eurocode 3
- Eurocode 5
- Eurocode 9
Materiały załączników krajowych
Gdzie znajdę materiały do odpowiednich załączników krajowych w programie RFEM 6 i RSTAB 9?
Pomijanie mas w programie RFEM 6/RSTAB 9
Jak mogę pominąć masy w analizie modalnej w programie RFEM 6/RSTAB 9?
Analiza stateczności ze stopniowym wzrostem obciążenia
Czy mogę stopniowo zwiększać obciążenie w programie RFEM 6 lub RSTAB 9?
Kierunek ortotropowy dla warstw
Dlaczego'nie mogę zdefiniować obrotu podczas definiowania warstw?
Ustawianie podpory pasa I dźwigara do obliczeń w rozszerzeniu Stateczność konstrukcji
W ramach rozszerzenia Projektowanie konstrukcji stalowych ustawiłem warunki brzegowe w taki sposób, aby pas I belki był zablokowany podczas poziomego przemieszczenia. Następnie obliczyłem współczynniki obciążenia krytycznego za pomocą rozszerzenia Stateczność konstrukcji, ale współczynnik obciążenia krytycznego nie miał wpływu na podporę. Jaki jest tego powód?
- 005437
- RFEM 6
- RSTAB 9
-
- Projektowanie konstrukcji stalowych RFEM 6
- Projektowanie konstrukcji stalowych RSTAB 9
- Połączenia stalowe RFEM 6
- Skręcanie skrępowane (7 stopni swobody) RFEM 6
- Skręcanie skrępowane (7 stopni swobody) RSTAB 9
- Konstrukcje stalowe
- Analiza statyczno-wytrzymałościowa
- Analiza naprężeń
- Sprawdzenie stateczności
- Analiza skręcania skrępowanego
- Połączenia stalowe
- Profile formowane na zimno
- Eurocode 3
- ANSI/AISC 360
- CSA S16
- IS 800
- GB 50017
- SP 63.13330
- BS 5950-1
- AS 4100
- SIA 263