68 Results
View Results:
Sort by:
Aluminum and Lightweight Structures
I would like to design an aluminum structure. Is it possible to use RFEM or RSTAB for this?
Effective Section
Can I calculate the effective section properties of a cross-section using RSECTION?
Add-ons for Concrete Structures
Which products do you recommend for the structural analysis and design of reinforced concrete structures?
Tensile Membrane Structures
Which Dlubal programs do I need for tensile membrane structures?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM
Temporary Structures
I would like to analyze temporary structures. Which programs do you recommend?
Programs for Timber Structures
Which Dlubal Software programs can I use to calculate and design timber structures?
- 005437
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Steel Joints for RFEM 6
- Torsional Warping (7 DOF) for RFEM 6
- Torsional Warping (7 DOF) for RSTAB 9
- Steel Structures
- Structural Analysis & Design
- Stress Analysis
- Stability Analysis
- Warping Torsion Analysis
- Steel Connections
- Cold-Formed Sections
- Eurocode 3
- ANSI/AISC 360
- CSA S16
- IS 800
- GB 50017
- SP 63.13330
- BS 5950-1
- AS 4100
- SIA 263
Programs for Steel Structures
Which programs and add-ons are suitable for the structural analysis and design of steel structures?
Cable and Tensile Structures
I would like to analyze cable and tensile structures. Is it possible to use RFEM or RSTAB for this?
Question
Why is it possible to switch off the individual design checks in RF‑/FOUNDATION Pro? After all, this poses a risk for the user to "accidentally" disable certain design checks and possibly design a foundation that is undersized?
Question
Is the exponent n applied differently from the design standard when determining the damage parameter ζ (zeta)?
AISC 341 Limit State Types
Which Limit State Types are applicable for the AISC 341 seismic design?
Question
How is the sliding resistance determined in FOUNDATION Pro?
Question
Why is the ground failure analysis not performed in RF‑/FOUNDATION Pro?
Question
How do I specify in FOUNDATION Pro which load is used for the design of the first core width, and which load is used for the design of the second core width?
Question
I would like to save foundations with certain dimensions as a template in the database. Is this possible? The button for this is disabled in Window "1.2 Geometry".
Question
I have to perform a recalculation of a foundation in the existing structure and search for a design according to DIN 1045 or DIN 1054. In RF‑/FOUNDATION Pro, only the Eurocode is available. Do you have any other modules for the foundation design?
Question
Can I rotate a foundation about the Z-axis in the RF‑FOUNDATION Pro add-on module?
Question
Is it possible to reinforce a foundation with a pure reinforcing bar?
Question
Where in the FOUNDATION Pro add‑on module can I activate the design for limiting a gaping joint according to DIN 1054:2010‑12 A 6.6.5?
Question
How do I activate the earth covering (permanent)? The corresponding check box is deactivated.
Question
How can the standard case tables be applied in RF‑/FOUNDATION Pro for the soil contact stress analysis?
Surface Reinforcement in Rib Design
How do I consider the surface (slab) reinforcement in my rib member (T-beam) design?
Custom Sections for AISI Design
Can I design user-defined (parametric) sections according to AISI S100 or CSA S136?
Question
Can RF‑STEEL AISC optimize cross-sections for serviceability?
Question
I have activated the settlement calculation in FOUNDATION Pro, but cannot export the determined stiffnesses of the nodal supports. Why not?
Stability Design in RF-STEEL AISC
Why are my steel members not being designed for stability in RF-STEEL AISC?
In RFEM 6, is it possible to display a graphic with the distribution of the required reinforcement in the DIN A0 format?
In RFEM 6, is it possible to display a graphic with the distribution of the required reinforcement in the DIN A0 format?
Question
Can I define soil layers for a soil profile with soil parameters myself?
Question
I am performing a design in RF‑/STEEL AISC for result combinations from RF‑/DYNAM Pro and get the error message "Not designable - Null value of the critical moment on the segment". What should I do?
- 005113
- Timber Design for RFEM 6
- Timber Design for RSTAB 9
-
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Stress-Strain Analysis for RFEM 6
- Stress-Strain Analysis for RSTAB 9
- Steel Joints for RFEM 6
- Timber Structures
- Concrete Structures
- Steel Structures
- Structural Analysis & Design
- Eurocode 2
- Eurocode 3
- Eurocode 5
- Eurocode 9