62 Results
View Results:
Sort by:
Stability Analysis According to EN 1999-1-1
Is it possible to perform stability analysis according to EN 1999‑1‑1 in RSECTION 1?
Aluminum and Lightweight Structures
I would like to design an aluminum structure. Is it possible to use RFEM or RSTAB for this?
Programs for Laminate and CLT Structures
Which programs do I need for laminate and sandwich structures, or cross-laminated timber (CLT)?
Effective Section
Can I calculate the effective section properties of a cross-section using RSECTION?
Add-ons for Concrete Structures
Which products do you recommend for the structural analysis and design of reinforced concrete structures?
Tensile Membrane Structures
Which Dlubal programs do I need for tensile membrane structures?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM
Temporary Structures
I would like to analyze temporary structures. Which programs do you recommend?
Programs for Timber Structures
Which Dlubal Software programs can I use to calculate and design timber structures?
Cable and Tensile Structures
I would like to analyze cable and tensile structures. Is it possible to use RFEM or RSTAB for this?
Graphic Templates for Printing Reinforcement Layout
How can I use graphic templates for multi printing of a reinforcement?
Question
Is the exponent n applied differently from the design standard when determining the damage parameter ζ (zeta)?
Question
For design, I need the load combinations from 1.00*G + 1.50*Q. How can I generate them automatically?
Question
What should be considered when using a failure of columns under tension in the RF‑/DYNAM Pro – Equivalent Loads add-on module?
Question
Are the models and presentations from Info Day 2019 freely available, and can you send them to me?
Question
Why does the web service show "ERROR: Map not found."?
Question
How is coupling between individual layers controlled in the RF‑LAMINATE add-on module?
Question
Where in the RF‑LAMINATE add-on module can I find which stress value is used for the design?
Question
Why is the "without glue at narrow sides" check box not selected by default in the RF‑LAMINATE add-on module?
Question
Why are the tolerance zones between the zone borders 5 km wide on the online snow load map of Austria?
Question
Is the compression reinforcement calculated for the ultimate limit state design in RF‑CONCRETE Surfaces? Or is it only possible in RF‑CONCRETE Members?
Question
How can I enter or read out a response spectrum via the COM interface in DYNAM Pro?
Hybrid Timber Cross-Section
Is it possible to display stresses of hybrid timber cross-sections in RFEM 5 and RSTAB 8?
Question
What does the "Calculate grid points result values for graphics" option set?
Surface Reinforcement in Rib Design
How do I consider the surface (slab) reinforcement in my rib member (T-beam) design?
Question
I am trying to verify RF‑CONCRETE Surfaces based on the results of the example in the manual. Chapter 2.4.3 describes the determination of the statically required reinforcement. Unfortunately, I cannot create an example that exactly represents these results. Can you send me the corresponding example?
Imposed Loads with Stiffness Modifications
I have defined temperature loads, strain loads, or a precamber. Once I modify stiffnesses, the deformations are no longer plausible.
RF-LAMINATE Library
How is it possible to display the RF‑LAMINATE library? We would like to check that it is up to date.
Switching Between Results in Grid Points and Mesh Nodes
Can I switch the required reinforcement in the result tables from "mesh nodes" to "grid points"?
In RFEM 6, is it possible to display a graphic with the distribution of the required reinforcement in the DIN A0 format?
In RFEM 6, is it possible to display a graphic with the distribution of the required reinforcement in the DIN A0 format?
- 004727
- RFEM 5
- RSTAB 8
-
- Concrete Structures
- Steel Structures
- Timber Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Finite Element Analysis
- Wind Simulation & Wind Load Generation
- Stability Analysis
- Dynamic and Seismic Analysis
- Form-Finding and Cutting Patterns
- Cold-Formed Sections
- Eurocode 1
- Eurocode 3
- Eurocode 5