36 Results
View Results:
Sort by:
Automatic Reinforcement Design
Can the RFEM 6 Concrete Design add-on automatically design member and surface reinforcement?
Is the deformation analysis in state II included in the concrete design in RFEM 6?
Is the deformation analysis in state II included in the concrete design in RFEM 6?
Line Hinge of Slab-Wall Connection
I would like to connect my masonry wall to a reinforced concrete slab. What is the best way to create a line hinge?
Member Design Supports for Deflection Checks
How do I define a member as a cantilever and not as supported at both ends for serviceability or deflection design?
Supports and Loads for Calculation with Warping Torsion
At which point on a cross-section are the supports and loads assumed for the calculation with warping torsion?
Results of Punching | Concrete design in RFEM 6
Where can I find the graphical results of punching shear in the concrete design? Especially the distribution of shear forces at the critical perimeter or the punching loads.
Cross-Section Warping
How can I display the cross-section warping?
Warping Spring and Warping Restraint
How can I define a warping spring or a warping restraint?
How can I open the interaction diagram from Concrete Design?
How can I open the interaction diagram from Concrete Design?
Why are the members not valid for the Concrete Design add-on?
Why are the members not valid for the Concrete Design add-on?
Warping Release
How do I set a release for warping?
Is it possible to design single-layer reinforced surfaces with RFEM 6?
Is it possible to design single-layer reinforced surfaces with RFEM 6?
Not Covered Reinforcement on Members | Concrete Design in RFEM 6 and RSTAB 9
Although all the member design checks have been fulfilled, I get the "Not Covered Reinforcement" result. What is the reason?
Nominal Reinforcement Bar Size
Can I define a different bar size in the RFEM 6 Concrete Design add-on other than the default bar sizes available in the drop-down?
Punching
I would like to perform punching design of a floor slab. I have selected nodes for the design, but they are marked as invalid. Where did I make a mistake?
Creep and Shrinkage of Concrete
Where can I activate creep or shrinkage for concrete design?
How can I check the way RFEM 6 determines the required reinforcement?
How can I check the way RFEM 6 determines the required reinforcement?
Case-Related Design with Different Load Situations
How can I carry out case-related design for different load situations?
Construction Stages - Modifying Properties
Is it possible to change the properties of members or surfaces, such as their location, in the individual construction stages?
Deactivating 7th Degree of Freedom by Member
How can I deactivate the 7th degree of freedom for only certain members or cross-sections?
Implausible Results – Torsional Warping
My results of the calculation with Torsional Warping are implausible. What could be the reason?
Surface Reinforcement in Rib Design
How do I consider the surface (slab) reinforcement in my rib member (T-beam) design?
Creating User-Defined Fabric
How do I create a user-defined fabric?
Membrane Structures
Is it possible also to design membrane structures in RFEM?
Activating Steel Fiber Concrete Design in "Concrete Design" Add-on
How can I activate the design with steel fiber-reinforced concrete in the "Concrete Design" add-on for RFEM 6?
Graphic Templates for Printing Reinforcement Layout
How can I use graphic templates for multi printing of a reinforcement?
Cable and Tensile Structures
I would like to analyze cable and tensile structures. Is it possible to use RFEM or RSTAB for this?
Not Valid/Deactivated Punching Nodes
In the table of the objects to be designed in the Concrete Design add-on, punching nodes are listed in the not valid/deactivated column, although I have defined them as punching nodes. How can I fix this?
Design Cases
Can I use design cases in RFEM 6 in the same way as in RFEM 5?
- 005437
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Steel Joints for RFEM 6
- Torsional Warping (7 DOF) for RFEM 6
- Torsional Warping (7 DOF) for RSTAB 9
- Steel Structures
- Structural Analysis & Design
- Stress Analysis
- Stability Analysis
- Warping Torsion Analysis
- Steel Connections
- Cold-Formed Sections
- Eurocode 3
- ANSI/AISC 360
- CSA S16
- IS 800
- GB 50017
- SP 63.13330
- BS 5950-1
- AS 4100
- SIA 263