The "Base Plate" component allows you to design base plate connections with cast-in anchors. In this case, plates, welds, anchorages, and steel-concrete interaction are analyzed.
In the Geotechnical Analysis add-on, the Hoek-Brown material model is available. The model shows linear-elastic ideal-plastic material behavior. Its nonlinear strength criterion is the most common failure criterion for stone and rocks.
You can enter the material parameters using
Rock parameters directly, or alternatively via
GSI classification.
Detailed information about this material model and the definition of the input in RFEM can be found in the respective chapter Hoek-Brown Model of the online manual for the Geotechnical Analysis add-on.
Using the "Rib" component, you can define any number of longitudinal ribs on a member plate. By defining a reference object, you can automatically specify welds on it.
The "Rib" component can also be arranged on circular hollow sections. Dafür wird zusätzlich die Vorgabe der Winkel zwischen den Rippen benötigt.
The Steel Joints add-on provides you with the option to connect circular hollow sections using welds.
It is possible to connect the circular sections to each other or to planar structural components. The fillets of standard and thin-walled sections can also be connected with a weld.
When designing connections, you can now also insert a new member as a component directly in the Steel Joints add-on. This will only be considered for the connection design. You can use the Weld and Fasteners components to connect to other members.
Furthermore, it is possible to use the Member Section and Member Editor components and arrange reinforcement elements on the inserted member, such as stiffeners and tapers.
Here, the weld design becomes child's play. Using the specially developed material model "Orthotropic | Plastic | Weld (Surfaces)", you can calculate all stress components plastically. The stress τperpendicular is also considered plastically.
Using this material model you can design welds closer to reality and more efficiently.
If a weld seam connects two plates with different materials, it is possible to select from a combo box in the Steel Joints add-on which one of both materials should be used for the weld seam.
In the case of rectangular cross-sections, you can usually achieve a direct connection by using welds. However, you can also connect them to other cross-sections in the same way. Furthermore, other components such as end plates help you to connect the rectangular cross-sections to other structural components.
In addition to other predefined components in the design add-on for steel connections, the universal base component "General Weld" can be used to enter complex connection situations.
Did you know? You can easily define structural modifications in load cases of the Modal Analysis type. This allows you, for example, to individually adjust the stiffnesses of materials, cross-sections, members, surfaces, hinges, and supports. You can also modify stiffnesses for some design add-ons. Once you select the objects, their stiffness properties are adapted to the object type. In this way, you can define them in separate tabs.
Do you want to analyze the failure of an object (for example, a column) in the modal analysis? This is also possible without any problems. Simply switch to the Structure Modification window and deactivate the relevant objects.
Did you know that To calculate masonry structures, a nonlinear material model has been implemented in RFEM. It is based on the approach of Lourenco, a composite yield surface according to Rankine and Hill. This model allows you to describe and model the structural behavior of masonry and the different failure mechanisms.
The limit parameters were selected in such a way that the design curves used correspond to a normative design curve.
Graphical display of the connection geometry that is updated in parallel with the input
The Steel Joints Template included in the add-on allows you to select from several connection types and, and once selected, it will be applied to your model.
Wide range of cross-section shapes: Includes I-sections, channel sections, angles, T-sections, built-up cross-sections, RHS (rectangular hollow sections), and thin-walled sections
The Template covers connections from three general categories: Rigid, Pinned, Truss
Automatic adaptation of the connection geometry, even if the structural components are subsequently edited, based on the relative relation of the components
In this case, you calculate the critical load factor for all analyzed load combinations and the selected number of mode shapes for the connection model. Compare the smallest critical load factor with the limit value 15 from the standard EN 1993‑1‑1, Clause 5. Furthermore, you can make user-defined adjustment of the limit value. As a result of the stability analysis, the program displays the corresponding mode shapes graphically.
For the stability analysis, RFEM uses the adapted surface model to specifically recognize the local buckling shapes. You can also save and use the model of the stability analysis, including the results, as a separate model file.
Compared to the RF‑/STEEL add-on module (RFEM 5 / RSTAB 8), the following new features have been added to the Stress-Strain Analysis add-on for RFEM 6 / RSTAB 9:
Treatment of members, surfaces, solids, welds (line welded joints between two and three surfaces with subsequent stress design)
Output of stresses, stress ratios, stress ranges, and strains
Limit stress depending on the assigned material or a user-defined input
Individual specification of the results to be calculated through freely assignable setting types
Non-modal result details with prepared formula display and additional result display on the cross-section level of members
Automatic generation of FE analysis models: The add-on automatically creates a finite element model (FE) of the steel connection in the background.
Consideration of all internal forces: The calculation and design checks include all internal forces (N, Vy, Vz, My, Mz, MT) and are not limited to planar loading.
Automatic load transfer: All load combinations are automatically transferred to the FE analysis model of the connection. The loads are transferred directly from RFEM, so manual data input is not necessary.
Efficient modeling: The add-on saves you time when modeling complex connection situations. You can also save the created FE analysis model and use it further for your own detailed analyses.
Extensible library: An extensive and extensible library with predefined steel connection templates is available.
Wide applicability: The add-on is suitable for connections of any type and shape, compatible with almost all rolled, welded, built-up, and thin-walled cross-sections.
No manual editing of the FE model required by the user, the essential calculation settings can be changed via the configuration settings
Automatic adaptation of the connection geometry, even if the members are subsequently edited, due to the relative relation of the components to each other
Parallel to the input, a plausibility check is carried out by the program to quickly detect missing input or collisions, for example
Graphical display of the connection geometry that is updated in parallel with the input
The program supports you: It determines the bolt forces on the basis of the FE analysis model and evaluates them automatically. The add-on performs the standard-compliant design of bolt resistance for failure cases, such as tension, shear, hole bearing, and punching, and clearly displays all required coefficients.
Do you want to perform weld design? The welds are modeled as elastic-plastic surface elements, and their stresses are read out from the FE analysis model. The plasticity criteria is set in the way that they represent failure according to AISC J2-4, J2-5 (strength of welds), and J2-2 (strength of base metal). The design can be performed with the partial safety factors of the selected National Annex of EN 1993‑1‑8.
The plates in the connection are designed plastically by comparing the existing plastic strain to the allowable plastic strain. The default setting is 5% according to EN 1993‑1‑5, Annex C, but can be adjusted by user-defined specifications, as well as 5% for AISC 360.
Do you want to perform the bending failure design? To do this, analyze the governing locations of the column for axial forces and moments. For the shear resistance design, you can also consider the locations with extreme values of shear forces. During the calculation, you determine whether a standard design is sufficient or whether the column with the moments has to be designed according to the second-order theory. You can then determine these moments using the previously entered specifications. The calculation is divided into three parts:
Load-independent calculation steps
Iterative determination of governing loading taking into account a varying required reinforcement
Safety determination of all acting internal forces, including the designed reinforcement
After a successful calculation, the results are displayed in clearly arranged tables. Each intermediate value is absolutely traceable, making the design checks transparent.
Simple definition of construction stages in the RFEM structure including visualization
Adding, removing, modifying, and reactivating member, surface, and solid elements and their properties (for example, member and line hinges, degrees of freedom for supports, and so on)
Automatic and manual combinatorics with load combinations in the individual construction stages (for example, to consider mounting loads, mounting cranes, and other loads)
Consideration of nonlinear effects such as tension member failure or nonlinear supports
Beam to Column joint category: connection possible as joint of the beam to the column flange as well as joint of the column to the girder flange
Beam to Beam joint category: design of beam joints as both moment-resisting end plate connections and rigid splice connections possible
Automatic export of model and load data possible from RFEM or RSTAB
Bolt sizes from M12 to M36 with strength grades 4.6, 4.8, 5.6, 5.8, 6.8, 8.8, and 10.9 as long as the strength grades are available in the selected National Annex
Almost any bolt spacing and edge distances (a check of the allowable distances is performed)
Beam strengthening with tapers or stiffeners on the top and bottom surfaces
End plate connection with and without overlap
Connection with pure bending stress, pure normal force load (tension joint), or combination of normal force and bending possible
Calculation of connection stiffnesses and check if a hinged, semi-rigid, or rigid connection exists
End plate connection in a beam-column setup
Joint beams or columns can be stiffened with tapers on one side or with stiffeners to one or both sides
Wide range of possible stiffeners of the connection (for example, complete or incomplete web stiffeners)
Up to ten horizontal and four vertical bolts possible
Connected object possible as constant or tapered I-section
Designs:
Ultimate limit state of the connected beam (such as shear or tension resistance of the web plate)
Ultimate limit state of the end plate at the beam (for example, T-stub under tensile stress)
Ultimate limit state of the welds at the end plate
Ultimate limit state of the column in the area of the connection (for example, column flange under bending – T-stub)
All designs are performed according to EN 1993-1-8 and EN 1993-1-1
Moment-resisting end plate joint
Two or four vertical and up to 10 horizontal bolt rows
Joint beams can be stiffened with tapers on one side or with stiffeners to one or both sides
Connected objects are possible as constant or tapered I-sections
Designs:
Ultimate limit state of the connected beams (such as shear or tension resistance of the web plates)
Ultimate limit state of the end plates at the beam (for example, T-stub under tensile stress)
Ultimate limit state of the welds at the end plates
Ultimate limit state of the bolts in the end plate (combination of tension and shear)
Rigid splice plate connection
For the flange plate connection, up to ten bolt rows one behind the other possible
For the web plate connection, up to ten bolt rows possible each in vertical and horizontal directions
Material of the cleat can be different from the one of the beams
Designs:
Ultimate limit state of the joint beams (for example, net cross-section in the tension area)
Ultimate limit state of the cleat plates (for example, net cross-section under tensile stress)
Ultimate limit state of the single bolts and the bolt groups (for example, shear resistance design of the single bolt)
At first, the governing joint designs are arranged in groups and displayed with the basic geometry of the joint in the first result window. In the other result windows, you can see all fundamental design details.
Dimensions, material properties, and welds important for the connection construction are displayed immediately and can be printed directly. Similarly, export to DXF-file is enabled. The connections can be visualized in the RF-/JOINTS Timber - Timber to Timber module as well as in RFEM/RSTAB.
All graphics can be included in the RFEM/RSTAB printout report or printed directly. Due to the scaled output, an optimal visual check is possible as early as in the design phase.
Import of materials, cross-sections, and internal forces from RFEM/RSTAB
Steel design of thin‑walled cross‑sections according to EN 1993‑1‑1:2005 and EN 1993‑1‑5:2006
Automatic classification of cross-sections according to EN 1993-1-1:2005 + AC:2009, Cl. 5.5.2, and EN 1993-1-5:2006, Cl. 4.4 (cross-section class 4), with optional determination of effective widths according to Annex E for stresses under fy
Integration of parameters for the following National Annexes:
DIN EN 1993-1-1/NA:2015-08 (Germany)
ÖNORM B 1993-1-1:2007-02 (Austria)
NBN EN 1993-1-1/ANB:2010-12 (Belgium)
BDS EN 1993-1-1/NA:2008 (Bulgaria)
DS/EN 1993-1-1 DK NA:2015 (Denmark)
SFS EN 1993-1-1/NA:2005 (Finland)
NF EN 1993-1-1/NA:2007-05 (France)
ELOT EN 1993-1-1 (Greece)
UNI EN 1993-1-1/NA:2008 (Italy)
LST EN 1993-1-1/NA:2009-04 (Lithuania)
UNI EN 1993-1-1/NA:2011-02 (Italy)
MS EN 1993-1-1/NA:2010 (Malaysia)
NEN EN 1993-1-1/NA:2011-12 (Netherlands)
NS EN 1993-1-1/NA:2008-02 (Norway)
PN EN 1993-1-1/NA:2006-06 (Poland)
NP EN 1993-1-1/NA:2010-03 (Portugal)
SR EN 1993-1-1/NB:2008-04 (Romania)
SS EN 1993-1-1/NA:2011-04 (Sweden)
SS EN 1993-1-1/NA:2010 (Singapore)
STN EN 1993-1-1/NA:2007-12 (Slovakia)
SIST EN 1993-1-1/A101:2006-03 (Slovenia)
UNE EN 1993-1-1/NA:2013-02 (Spain)
CSN EN 1993-1-1/NA:2007-05 (Czech Republic)
BS EN 1993-1-1/NA:2008-12 (the United Kingdom)
CYS EN 1993-1-1/NA:2009-03 (Cyprus)
In addition to the National Annexes (NA) listed above, you can also define a specific NA, applying user‑defined limit values and parameters.
Automatic calculation of all required factors for the design value of flexural buckling resistance Nb,Rd
Automatic determination of the ideal elastic critical moment Mcr for each member or set of members on every x-location according to the Eigenvalue Method or by comparing moment diagrams. You only have to define the lateral intermediate supports.
Design of tapered members, unsymmetric sections or sets of members according to the General Method as described in EN 1993-1-1, Cl. 6.3.4
In the case of the General Method according to Cl. 6.3.4, optional application of "European lateral-torsional buckling curve" according to Naumes, Strohmann, Ungermann, Sedlacek (Stahlbau 77 [2008], pp. 748‑761)
Rotational restraints can be taken into account (trapezoidal sheeting and purlins)
Optional consideration of shear panels (for example, trapezoidal sheeting and bracing)
RF-/STEEL Warping Torsion module extension (license required) for stability analysis according to the second-order analysis as stress analysis including consideration of the 7th degree of freedom (warping)
Module extension RF-/STEEL Plasticity (license required) for plastic analysis of cross‑sections according to Partial Internal Forces Method (PIFM) and Simplex Method for general cross‑sections (in connection with the RF‑/STEEL Warping Torsion module extension, it is possible to perform the plastic design according to the second‑order analysis)
Module extension RF-/STEEL Cold-Formed Sections (license required) for ultimate and serviceability limit state designs for cold-formed steel members according to the EN 1993-1-3 and EN 1993-1-5 standards
ULS design: Selection of fundamental or accidental design situations for each load case, load combination, or result combination
SLS design: Selection of characteristic, frequent, or quasi-permanent design situations for each load case, load combination, or result combination
Tension analysis with definable net cross-section areas for member start and end
Weld designs of welded cross-sections
Optional calculation of warp spring for nodal support on sets of members
Graphic of design ratios on cross-section and in RFEM/RSTAB model
Determination of governing internal forces
Filter options for graphical results in RFEM/RSTAB
Representation of design ratios and cross‑section classes in the rendered view
Color scales in result windows
Automatic cross-section optimization
Transfer of optimized cross-sections to RFEM/RSTAB
Parts lists and quantity surveying
Direct data export to MS Excel
Verifiable printout report
Possibility to include the temperature curve in the report
RF-CUTTING-PATTERN is activated by selecting the respective option in the Options tab in General Data of any RFEM model. After activating the add‑on module, a new object, "Cutting Patterns", is displayed under Model Data. If the membrane surface distribution for cutting in the basic position is too large, you can divide the surface by cutting lines (line types "Cut via Two Lines" or "Cut via Section") in the corresponding partial strips.
Then you can define the individual entries for each cutting pattern using the "Cutting Pattern" object. Here you can set boundary lines, compensations, and allowances.
Steps of the working sequence:
Creation of cutting lines
Creation of the pattern by selecting its boundary lines or using a semi‑automatic generator
Free selection of warp and weft orientation by entering an angle
Application of compensation values
Optional definition of different compensations for boundary lines
Different allowances (welding, boundary line)
Preliminary representation of the cutting pattern in the graphic window at the side without starting the main nonlinear calculation