31 Results
View Results:
Sort by:
Question
I would like to calculate a hall frame with loads from a crane runway. It is not quite clear to me what the various action categories denote. Can you explain it to me?
Question
How do I superimpose generated equivalent loads from the seismic analysis?
Question
For design, I need the load combinations from 1.00*G + 1.50*Q. How can I generate them automatically?
Question
Why does the web service show "ERROR: Map not found."?
Question
Are the models and presentations from Info Day 2019 freely available, and can you send them to me?
Question
Why are the tolerance zones between the zone borders 5 km wide on the online snow load map of Austria?
Question
How can I determine loads at particular geographic coordinates in the online service "Snow Load, Wind Speed, and Seismic Load Maps"?
Question
How do I determine the stiffness center of my structural system?
Question
Is it also possible to integrate the online service "Snow Load, Wind Speed, and Seismic Load Maps" into external applications?
Question
Is the exponent n applied differently from the design standard when determining the damage parameter ζ (zeta)?
Question
How are the location-specific Geo-Zone Tool data queries calculated for the determination of various building loads?
Question
Why is the load value displayed in the online service "Geo-Zone Tool: Snow Load, Wind Speed, and Seismic Load Maps" different from the value in the corresponding standard in some cases?
Question
Is it possible to generate wind loads according to DIN EN 13782 with this program?
Question
When designing seismic equivalent loads with a Response Spectra Analysis (RSA) in RFEM, how can I apply the modal response parameters Ie/R according to Sect. 12.9.1.2 in the ASCE‑7‑16 to my results?
Question
Is the Gust-effect (G or Gf) from the ASCE 7‑16 Sect. 26.11 considered in RWIND Simulation?
Question
Is it possible to perform automatic live load reduction in RFEM or RSTAB per the ASCE, IBC, or NBCC?
Question
How can I enter or read out a response spectrum via the COM interface in DYNAM Pro?
- 004727
- RFEM 5
- RSTAB 8
-
- Concrete Structures
- Steel Structures
- Timber Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Finite Element Analysis
- Wind Simulation & Wind Load Generation
- Stability Analysis
- Dynamic and Seismic Analysis
- Form-Finding and Cutting Patterns
- Cold-Formed Sections
- Eurocode 1
- Eurocode 3
- Eurocode 5
Question
Are the models and presentations from Info Day 2020 freely available, and can you send them to me?
Question
What should be considered when using a failure of columns under tension in the RF‑/DYNAM Pro – Equivalent Loads add-on module?
Question
RF‑STEEL AISC add-module shows non-designable results for general cross-sections because of shear buckling checks according to Chapter G. How do I solve this?
- 005113
- Timber Design for RFEM 6
- Timber Design for RSTAB 9
-
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Stress-Strain Analysis for RFEM 6
- Stress-Strain Analysis for RSTAB 9
- Steel Joints for RFEM 6
- Timber Structures
- Concrete Structures
- Steel Structures
- Structural Analysis & Design
- Eurocode 2
- Eurocode 3
- Eurocode 5
- Eurocode 9
Materials of National Annexes
Where can I find the materials for the corresponding National Annexes in RFEM 6 and RSTAB 9?
In RFEM 6, is it possible to display a graphic with the distribution of the required reinforcement in the DIN A0 format?
In RFEM 6, is it possible to display a graphic with the distribution of the required reinforcement in the DIN A0 format?
ASCE 7 Orthogonal Directional Combination Procedure
How do I apply the ASCE 7 Orthogonal Directional Combination procedure (100% + 30% rule) to my seismic load in a static analysis?
ASCE 7 Seismic Load Combinations
I do not see the seismic load cases in my generated ASCE 7 load combinations (COs). How do I add them?
ASCE 7 Reduced Live Load Factor
My live load is less than or equal to 100 psf. How do I consider the reduced load factor in the ASCE 7 load combinations?
Surface Reinforcement in Rib Design
How do I consider the surface (slab) reinforcement in my rib member (T-beam) design?
Cable and Tensile Structures
I would like to analyze cable and tensile structures. Is it possible to use RFEM or RSTAB for this?
Tensile Membrane Structures
Which Dlubal programs do I need for tensile membrane structures?
Aluminum and Lightweight Structures
I would like to design an aluminum structure. Is it possible to use RFEM or RSTAB for this?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM