31 Results
View Results:
Sort by:
Question
What are the stiffness reduction factors k33 and k88 in the Multilayer Surfaces Add-on?
- 005113
- Timber Design for RFEM 6
- Timber Design for RSTAB 9
-
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Stress-Strain Analysis for RFEM 6
- Stress-Strain Analysis for RSTAB 9
- Steel Joints for RFEM 6
- Timber Structures
- Concrete Structures
- Steel Structures
- Structural Analysis & Design
- Eurocode 2
- Eurocode 3
- Eurocode 5
- Eurocode 9
Materials of National Annexes
Where can I find the materials for the corresponding National Annexes in RFEM 6 and RSTAB 9?
Analyse de déformation
Is it possible to display the deformation analysis of a surface (limit 0.5‰)?
Line Hinge of Slab-Wall Connection
I would like to connect my masonry wall to a reinforced concrete slab. What is the best way to create a line hinge?
Design of Member Sets
I have activated Steel Design in my model and defined design types for the members. Why can I not design the superordinate member set?
Adapted Method (Enable Double Bending)
I cannot analyze a UPN cross-section subjected to double bending in the program. Is it possible to do this in the program?
Unsymmetrical Cross-Section (UPE)
I am having trouble with the design of a steel structure. For a singly symmetric cross-section (UPE), the program cannot perform the stability analysis. It reports that the Equivalent Member Method 6.3.3 is not applicable for an unsymmetrical cross-section. Is it possible to design such cross-sections in the program?
Member Design Supports for Deflection Checks
How do I define a member as a cantilever and not as supported at both ends for serviceability or deflection design?
Construction Stages - Modifying Properties
Is it possible to change the properties of members or surfaces, such as their location, in the individual construction stages?
Effective Lengths for Steel Stability Design
How do I define effective lengths when designing steel members in RFEM 6?
Stress Ratio
The limit stress is activated, but my stress ratio is “non-designable” in the Stress-Strain Analysis add-on. What could be the reason?
Implausible Results – Torsional Warping
My results of the calculation with Torsional Warping are implausible. What could be the reason?
Case-Related Design with Different Load Situations
How can I carry out case-related design for different load situations?
Redundancy Factors
How do I include the redundancy factor(s) ρ in the ASCE 7 load combinations?
Overstrength Factors
How do I include the overstrength factor(s) Ωo in the ASCE 7 load combinations?
Orthotropy Direction for Layers
Why cannot I define a rotation when defining layers?
Surface Type Error
I received an error message “Surface of incompatible type... (Surface in upper plane of building story must be of ‘Load transfer’ type)” when running the calculation. What is the reason?
Exclude Lateral Torsional Buckling Check
My beam has a continuous lateral support and therefore lateral torsional buckling (LTB) is not a concern. How do I define the effective length?
Standardized Sections for AISI Design
Which standardized sections are valid for AISI cold-formed steel design in RFEM 6?
Custom Sections for AISI Design
Can I design user-defined (parametric) sections according to AISI S100 or CSA S136?
AISI Table B4.1-1 Applicability Limits
Does RFEM check the applicability limits of AISI Table B4.1‑1?
Instability when Using Building Model with "Rigid Diaphragm"
I have a 3D model and try to split it up into "walls" and "surfaces" with the Building Model and to calculate them separately. However, my structural system becomes unstable then. What can be the reason?
CSA S16 Class 4 Sections
Can I design members with Class 4 sections according to CSA S16 in the Steel Design add-on?
- 005437
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Steel Joints for RFEM 6
- Torsional Warping (7 DOF) for RFEM 6
- Torsional Warping (7 DOF) for RSTAB 9
- Steel Structures
- Structural Analysis & Design
- Stress Analysis
- Stability Analysis
- Warping Torsion Analysis
- Steel Connections
- Cold-Formed Sections
- Eurocode 3
- ANSI/AISC 360
- CSA S16
- IS 800
- GB 50017
- SP 63.13330
- BS 5950-1
- AS 4100
- SIA 263
Programs for Steel Structures
Which programs and add-ons are suitable for the structural analysis and design of steel structures?
Tensile Membrane Structures
Which Dlubal programs do I need for tensile membrane structures?
Scaffolding and Rack Structures
We are looking for a program for scaffolding and rack structures. Is Dlubal Software suitable for this?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM