78 Results
View Results:
Sort by:
Adjusting NDS and CSA O86 Factors for Consideration in the Timber Design Add-on
How can the NDS and CSA O86 factors be manually adjusted for consideration in the Timber Design add-on?
NDS Strength Configuration - Calculation of Torsion Settings
What calculation is carried out for the NDS Strength Configuration "Calculation of Torsion" options?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM
Temporary Structures
I would like to analyze temporary structures. Which programs do you recommend?
Aluminum and Lightweight Structures
I would like to design an aluminum structure. Is it possible to use RFEM or RSTAB for this?
Programs for Timber Structures
Which Dlubal Software programs can I use to calculate and design timber structures?
- 005437
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Steel Joints for RFEM 6
- Torsional Warping (7 DOF) for RFEM 6
- Torsional Warping (7 DOF) for RSTAB 9
- Steel Structures
- Structural Analysis & Design
- Stress Analysis
- Stability Analysis
- Warping Torsion Analysis
- Steel Connections
- Cold-Formed Sections
- Eurocode 3
- ANSI/AISC 360
- CSA S16
- IS 800
- GB 50017
- SP 63.13330
- BS 5950-1
- AS 4100
- SIA 263
Programs for Steel Structures
Which programs and add-ons are suitable for the structural analysis and design of steel structures?
CSA S16 Class 4 Sections
Can I design members with Class 4 sections according to CSA S16 in the Steel Design add-on?
Equivalent Round Section Dimension
How is the dimension for an equivalent round section calculated in the Timber Design add-on?
Exclude Lateral Torsional Buckling Check
My beam has a continuous lateral support and therefore lateral torsional buckling (LTB) is not a concern. How do I define the effective length?
Line Hinges on Several Surfaces
How can I efficiently define line hinges on several surfaces?
Orthotropy Direction for Layers
Why cannot I define a rotation when defining layers?
Strength of Weld-Affected Zone for Aluminum
How do I consider the strength of weld-affected zone for aluminum?
Where can I activate the reduction of load combinations in RFEM 6? And how does this reduction work?
Where can I activate the reduction of load combinations in RFEM 6? And how does this reduction work?
Favorable Permanent Actions
Where can I activate the "Favorable permanent actions" option in RFEM 6 and RSTAB 9 in order to combine the self-weight in the ultimate limit state with 1.0?
Load Transfer Surface RWIND
Is it possible to use load transfer surfaces in RFEM 6 for wind load generation using RWIND?
Combinations for Road Bridges According to EN 1991-2 in RFEM 6
Does RFEM 6 include the combinations for road bridges according to EN 1991‑2?
Question
I am designing a cross-section created in the SHAPE‑THIN program using the design add-on module, but the program shows the error message "ER006 Invalid type of c/t-part for cross-section of type General". What can I do?
Question
The online service "Snow Load, Wind Speed, and Seismic Load Maps" displays the snow load zones 1*, 1a*, 2*, and 3* for Germany. Where are these snow load zones defined?
Question
How is it possible to display the main support direction graphically in RF‑LAMINATE?
CSA S16 Class 4 Section
My section is classified as Class 4 and non-designable in RF-/STEEL CSA. However, my manual calculation shows a different class. Why the difference?
Question
In RF-/TIMBER AWC and RF-/TIMBER CSA, I receive the error that says torsion limit exceeded. How do I bypass this error message?
Question
How can I apply wind load distribution to a cylinder according to EN 1991‑4, Section 7.9?
Question
I noticed deviations from my sources in the online service "Snow Load, Wind Speed, and Seismic Load Maps". Where can I find information about the sources of your online service?
Geo-zone tool
I noticed deviations from the map of DIN EN 1998‑1 or DIN 4149 in the online service "Geo-Zone Tool: Snow Load, Wind Speed, and Seismic Load Maps". Can you tell me which map is current and thus governing?
Question
How can I design dowel-laminated timber (DLT) or nail-laminated timber (NLT) in RFEM?
Question
How can I perform a stability analysis for a tapered member?
- 004727
- RFEM 5
- RSTAB 8
-
- Concrete Structures
- Steel Structures
- Timber Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Finite Element Analysis
- Wind Simulation & Wind Load Generation
- Stability Analysis
- Dynamic and Seismic Analysis
- Form-Finding and Cutting Patterns
- Cold-Formed Sections
- Eurocode 1
- Eurocode 3
- Eurocode 5