77 Results
View Results:
Sort by:
Implementation of Experimental Wind Tunnel Data in RFEM
How we can introduce experimental wind tunnel data in RFEM?
Implementation of Experimental Wind Tunnel Data in RWIND
How we can introduce experimental data in RWIND?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM
Temporary Structures
I would like to analyze temporary structures. Which programs do you recommend?
Power Plants and Conveyor Structures
Which programs can I use to design power plants and conveyor structures?
Aluminum and Lightweight Structures
I would like to design an aluminum structure. Is it possible to use RFEM or RSTAB for this?
- 005437
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Steel Joints for RFEM 6
- Torsional Warping (7 DOF) for RFEM 6
- Torsional Warping (7 DOF) for RSTAB 9
- Steel Structures
- Structural Analysis & Design
- Stress Analysis
- Stability Analysis
- Warping Torsion Analysis
- Steel Connections
- Cold-Formed Sections
- Eurocode 3
- ANSI/AISC 360
- CSA S16
- IS 800
- GB 50017
- SP 63.13330
- BS 5950-1
- AS 4100
- SIA 263
Programs for Steel Structures
Which programs and add-ons are suitable for the structural analysis and design of steel structures?
Earthquake Data in Geo-Zone Tool According to DIN EN 1998
How does the Geo-zone tool determine the earthquake data according to DIN EN 1998‑1?
Exclude Lateral Torsional Buckling Check
My beam has a continuous lateral support and therefore lateral torsional buckling (LTB) is not a concern. How do I define the effective length?
Creating Response Spectrum ASCE 7-22
How can I create a response spectrum according to ASCE 7‑22?
Strength of Weld-Affected Zone for Aluminum
How do I consider the strength of weld-affected zone for aluminum?
Mode Shapes - Limiting Selection of Shapes
I need many mode shapes to achieve a sum of 90% effective modal mass. Can I limit the number of mode shapes for generating equivalent loads?
Where can I activate the reduction of load combinations in RFEM 6? And how does this reduction work?
Where can I activate the reduction of load combinations in RFEM 6? And how does this reduction work?
Favorable Permanent Actions
Where can I activate the "Favorable permanent actions" option in RFEM 6 and RSTAB 9 in order to combine the self-weight in the ultimate limit state with 1.0?
National Annex DIN EN 1998-1/NA:2021-07
Is the German National Annex 2021‑07 to Eurocode 8 available in RFEM 5 / RSTAB 8?
Load Transfer Surface RWIND
Is it possible to use load transfer surfaces in RFEM 6 for wind load generation using RWIND?
Combinations for Road Bridges According to EN 1991-2 in RFEM 6
Does RFEM 6 include the combinations for road bridges according to EN 1991‑2?
Question
RF‑/DYNAM Pro – Forced Vibrations and RF‑/DYNAM Pro – Equivalent Loads perform the multi-modal response spectrum analysis. What are the differences?
Question
I am designing a cross-section created in the SHAPE‑THIN program using the design add-on module, but the program shows the error message "ER006 Invalid type of c/t-part for cross-section of type General". What can I do?
Question
What method is applied in the RF‑/DYNAM Pro - Equivalent Loads add-on module?
Question
The online service "Snow Load, Wind Speed, and Seismic Load Maps" displays the snow load zones 1*, 1a*, 2*, and 3* for Germany. Where are these snow load zones defined?
Question
I have used the RF‑/DYNAM Pro add-on module to generate the governing result combinations of seismic loads. What is the next procedure to perform the design of the individual structural components?
Question
What should be considered when using a failure of columns under tension in the RF‑/DYNAM Pro – Equivalent Loads add-on module?
Question
How can I apply wind load distribution to a cylinder according to EN 1991‑4, Section 7.9?
Question
I would like to perform seismic design of an irregular structure. Does RFEM automatically carry out the modal analysis (consideration of multiple vibration modes) on the spatial system, or do I have to use special settings for this?
Question
I noticed deviations from my sources in the online service "Snow Load, Wind Speed, and Seismic Load Maps". Where can I find information about the sources of your online service?
Geo-zone tool
I noticed deviations from the map of DIN EN 1998‑1 or DIN 4149 in the online service "Geo-Zone Tool: Snow Load, Wind Speed, and Seismic Load Maps". Can you tell me which map is current and thus governing?
Question
How do you distinguish between the response spectrum with equivalent loads method and the response spectrum without equivalent loads method in RFEM and RSTAB?
Question
Why can I only calculate seismic loads in one direction when using RF‑/DYNAM Pro?
- 004727
- RFEM 5
- RSTAB 8
-
- Concrete Structures
- Steel Structures
- Timber Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Finite Element Analysis
- Wind Simulation & Wind Load Generation
- Stability Analysis
- Dynamic and Seismic Analysis
- Form-Finding and Cutting Patterns
- Cold-Formed Sections
- Eurocode 1
- Eurocode 3
- Eurocode 5