Podczas obliczania siły tnącej w programie Wymiarowanie betonu zbrojonego, działającą siłę tnącą Vz można zredukować zgodnie z EN 1992-1-1. Poniższy artykuł opisuje redukcję siły tnącej od obciążeń skupionych w pobliżu podpory oraz wymiarowanie sił tnących w odległości d od krawędzi podpory w przypadku obciążenia równomiernie rozłożonego.
Za pomocą programów RWIND 2 i RFEM 6 można teraz obliczać obciążenia wiatrem na podstawie zmierzonego eksperymentalnie ciśnienia wiatru na powierzchnie. Zasadniczo dostępne są dwie metody interpolacji, umożliwiające rozłożenie ciśnienia mierzonego w izolowanych punktach na powierzchnie. Żądany rozkład ciśnienia można uzyskać za pomocą odpowiedniej metody i ustawień parametrów.
Wydarzenia ostatnich lat przypominają nam o znaczeniu konstrukcji odpornych na trzęsienia ziemi w zagrożonych regionach. Projektowanie konstrukcji na obszarach narażonych na trzęsienia ziemi jest ciągłym kompromisem między efektywnością ekonomiczną i możliwościami finansowymi, a także bezpieczeństwem. Jeżeli zawalenie jest nieuniknione, należy ocenić, w jaki sposób wpłynie ono na konstrukcję. Celem tego artykułu jest przedstawienie jednej z opcji przeprowadzenia tej oceny.
Nasza usługa sieciowa oferuje użytkownikom możliwość komunikacji z programami RFEM 6 i RSTAB 9 za pomocą różnych języków programowania. Funkcje wysokiego poziomu (HLF) firmy Dlubal umożliwiają rozszerzenie i uproszczenie funkcjonalności WebService. Zgodnie z RFEM 6 i RSTAB 9, korzystanie z naszego webservice sprawia, że praca inżyniera jest łatwiejsza i szybsza. Wypróbuj teraz! Ten samouczek pokazuje, jak korzystać z biblioteki C #na prostym przykładzie.
Aby umożliwić ocenę wpływu lokalnych zjawisk stateczności smukłych elementów, w programach RFEM 6 i RSTAB 9 można przeprowadzić liniową analizę obciążenia krytycznego na poziomie przekroju. Poniższy artykuł poświęcony jest podstawom obliczeń i interpretacji wyników.
W tym artykule pokazano, w jaki sposób rozszerzenie „Analiza zależna od czasu” jest zintegrowane w programach RFEM 6 i RSTAB 9. Opisuje sposób definiowania danych wejściowych, takich jak charakterystyka materiału zależna od czasu, sposób określania typu analizy i czasy obciążenia.
Podobnie jak w przypadku poprzednich generacji programów firmy Dlubal, zintegrowany interfejs z Autodesk Revit jest teraz dostępny dla programów RFEM 6 i RSTAB 9. W tym artykule przedstawiono ogólne informacje na temat interfejsu oraz obiektów konstrukcyjnych i parametrów związanych z firmą Dlubal w programie Revit.
Programy do arkuszy kalkulacyjnych, takie jak EXCEL, są popularne wśród inżynierów, ponieważ można z łatwością zautomatyzować obliczenia i szybko uzyskać wyniki. Połączenie programu MS EXCEL jako graficznego interfejsu użytkownika z WebService API jest zatem oczywiste. Za pomocą bezpłatnej biblioteki xlwings dla Pythona można sterować programem EXCEL oraz odczytywać i zapisywać wartości. Funkcjonalność tę wyjaśniono poniżej na przykładzie.
Steel Joist Institute (SJI) wcześniej opracował tabele wirtualnych belek nośnych w celu oszacowania właściwości przekroju dla belek stalowych z otwartym środnikiem. Te przekroje belek wirtualnych są scharakteryzowane jako równoważne belki o szerokich półkach, które są bardzo zbliżone do pola powierzchni pasa, efektywnego momentu bezwładności i ciężaru. Wirtualne belki nośne są również dostępne w bazie danych przekrojów w programach RFEM i RSTAB.
W programach RFEM 6 i RSTAB 9 można grupować obiekty według różnych kryteriów. Dzięki temu można jednocześnie wybierać i edytować obiekty spełniające zdefiniowane kryteria. Jest to możliwe dzięki narzędziu „Wybór obiektu”, które jest porównywalne z narzędziem „Wybór specjalny” w programie RFEM 5. W tym artykule dowiesz się, jak pogrupować obiekty za pomocą opcji „Wybór obiektów” jako nowy obiekt pomocniczy w programie RFEM 6 lub RSTAB 9.
API dla RFEM 6, RSTAB 9 i RSECTION opiera się na koncepcji usług sieciowych (Webservice). Aby zapoznać się z tematem, w poniższym artykule omawiamy kolejny przykład w języku C#.
W tym artykule pokazano, jak definiować różne typy usztywnień poprzecznych pręta w programie RFEM 6 i RSTAB 9. Pokazano tu również, w jaki sposób uwzględnić je w projektowaniu i obliczeniach prętów o 7 stopniach swobody.
Standardowym rozwiązaniem w konstrukcji prętów drewnianych jest możliwość łączenia mniejszych prętów poprzez podparcie na większym dźwigarze. Dodatkowo warunki na końcach pręta mogą uwzględniać podobną sytuację, w której belka jest oparta na podporze. W obu przypadkach belka musi być zaprojektowana tak, aby uwzględniała nośność w poprzek włókien zgodnie z NDS 2018 s. 3.10.2 i CSA O86:19 punkty 6.5.6 i 7.5.9. W ogólnych programach do projektowania statyczno-wytrzymałościowego zazwyczaj nie jest możliwe przeprowadzenie pełnej kontroli obliczeń, ponieważ powierzchnia docisku jest nieznana. Jednak w programie RFEM 6 nowej generacji i rozszerzeniu Projektowanie konstrukcji drewnianych dodana funkcja "podpór obliczeniowych" umożliwia teraz użytkownikom uwzględnienie docisku NDS i CSA prostopadle do warunków obliczeniowych.
Analiza modalna jest punktem wyjścia do analizy dynamicznej układów konstrukcyjnych. Można ją wykorzystać do określenia wartości drgań własnych, takich jak częstotliwości drgań własnych, kształty drgań własnych, masy modalne i efektywne współczynniki masy modalnej. Wynik ten może zostać wykorzystany do obliczeń drgań oraz do dalszych analiz dynamicznych (na przykład obciążenia widmem odpowiedzi).
Webservice to komunikacja między maszynami i programami. Komunikacja ta odbywa się za pośrednictwem sieci i dlatego może być wykorzystywana przez dowolny program, który może wysyłać i odbierać ciągi znaków za pośrednictwem protokołu HTTP. Programy RFEM 6 i RSTAB 9 zapewniają interfejs oparty na tych wieloplatformowych usługach sieciowych. Ten tutorial pokazuje podstawy korzystania z języka programowania VBA.
Wraz z programami do analizy statyczno-wytrzymałościowej RFEM 6, RSTAB 9, RSECTION 1 i RWIND 2, Dlubal Software przedstawia nową generację programów do analizy statyczno-wytrzymałościowej. Getreu dem Motto „Statik, die Spaß macht…“ werden den Anwendern universelle Werkzeuge in die Hand gegeben, mit denen alle Anforderungen in der Tragwerksplanung bewältigt werden können. Was sich sonst noch bei Dlubal Software Neues getan hat, erfahren Sie in diesem Artikel.
Parametry przekrojów walcowanych, najpopularniejszego typu przekrojów w programach RFEM i RSTAB, również mogą zostać zdefiniowane przez użytkownika. W tym celu należy zaznaczyć przekrój do modyfikacji w bibliotece przekrojów i kliknąć przycisk [Wprowadzanie parametryczne ...].
W programach RFEM i RSTAB dostępne są różne opcje zmiany numeracji poszczególnych elementów konstrukcyjnych, takich jak węzły, linie, pręty, powierzchnie lub bryły. Istnieją dwie możliwości zmiany numeracji: pojedynczo i automatycznie.
Häufig verhindern sehr kleine Torsionsmomente in den zu bemessenden Stäben bestimmte Nachweisformate. Um diese zu vernachlässigen und die Nachweise dennoch zu führen, kann man in RF-/STAHL EC3 einen Grenzwert definieren, ab dem Torsionsschubspannungen berücksichtigt werden.
Die zusätzlichen Lasten aus Eigengewicht setzen sich in der Regel aus mehreren Schichten zusammen, wie zum Beispiel dem klassischen Fußboden- und Dachaufbau im Hochbau oder dem Fahrbahnaufbau bei Brückentragwerken. Bei der Lastdefinition in RFEM und RSTAB können mittels Verwendung der Mehrschichtaufbau-Last die einzelnen Schichten mit Dicke und spezifischem Gewicht definiert werden.
Stateczność konstrukcji nie jest nowym zjawiskiem w odniesieniu do projektowania konstrukcji stalowych. Kanadyjska norma CSA S16 dotycząca projektowania konstrukcji stalowych i najnowsza wersja na rok 2019 nie stanowią wyjątku. Szczegółowe wymagania dotyczące stateczności można uwzględnić za pomocą uproszczonej procedury analizy stateczności z punktu 8.4.3. lub zgodnie z nowymi zapisami w wersji z 2019, za pomocą efektów stateczności w procedurze analizy sprężystej wg. załącznika O.