Search Result
12 result(s) for " 钢筋"
Adjusting Grid
/en/downloads-and-information/documents/online-manuals/webinar-modeling-and-design-of-solid-elements-in-rfem-6/003985
Creating Result Section
/en/downloads-and-information/documents/online-manuals/webinar-modeling-and-design-of-solid-elements-in-rfem-6/004003
Creating Surface Supports
/en/downloads-and-information/documents/online-manuals/webinar-modeling-and-design-of-solid-elements-in-rfem-6/003998
Documentation in Printout Report
/en/downloads-and-information/documents/online-manuals/webinar-modeling-and-design-of-solid-elements-in-rfem-6/004002
Entering Bolt and Contact Solid
/en/downloads-and-information/documents/online-manuals/webinar-modeling-and-design-of-solid-elements-in-rfem-6/003988
Entering Structure
/en/downloads-and-information/documents/online-manuals/webinar-modeling-and-design-of-solid-elements-in-rfem-6/003986
Hole Solid Type
/en/downloads-and-information/documents/online-manuals/webinar-modeling-and-design-of-solid-elements-in-rfem-6/003987
Line Welded Joint
/en/downloads-and-information/documents/online-manuals/webinar-modeling-and-design-of-solid-elements-in-rfem-6/004000
Loads
/en/downloads-and-information/documents/online-manuals/webinar-modeling-and-design-of-solid-elements-in-rfem-6/003992
Mesh Quality
/en/downloads-and-information/documents/online-manuals/webinar-modeling-and-design-of-solid-elements-in-rfem-6/003999
Splice Modeling
/en/downloads-and-information/documents/online-manuals/webinar-modeling-and-design-of-solid-elements-in-rfem-6/003969
Stress-Strain Analysis
/en/downloads-and-information/documents/online-manuals/webinar-modeling-and-design-of-solid-elements-in-rfem-6/004001
Length: 01:05:28 min
Length: 00:45:08 min
Length: 01:04:41 min
Length: 00:59:36 min
Length: 01:15:10 min
Length: 01:07:03 min
Length: 00:00:50 min
Length: 01:08:12 min
In this article, you will learn how to model and design cable structures in RFEM 6 or RSTAB 9.
This article describes and explains the influence of bending stiffness of cables on their internal forces. Furthermore, the text provides information on how this influence can be reduced.
The ASCE 7-22 Standard [1], Sect. 12.9.1.6 specifies when P-delta effects should be considered when running a modal response spectrum analysis for seismic design. In the NBC 2020 [2], Sent. 4.1.8.3.8.c gives only a short requirement that sway effects due to the interaction of gravity loads with the deformed structure should be considered. Therefore, there may be situations where second-order effects, also known as P-delta, must be considered when carrying out a seismic analysis.
The data exchange between RFEM 6 and Allplan can be done using various file formats. This article describes the data exchange of a determined surface reinforcement using the ASF interface. This allows you to display the RFEM reinforcement values as level curves or colored reinforcement images in Allplan.
In RFEM 6, it is possible to define line welds between surfaces and to calculate the weld stresses using the Stress-Strain Analysis add-on.
The following joint types are available:
- Butt Joint
- Corner joint
- Lap Joint
- T-joint
Depending on the selected joint type, you can select the following weld types:
- Single Square
- Double Square
- Double Bevel
- Single V
- Double V
- Single U
- Double U
- Single J
- Double J
In addition to JavaScript, the Python high-level functions are also available in the console. Using the Python option, the console also provides you with the Python HLF functions known from the WebService function catalog for further use in the object properties dialog box for in-app scripting.
In the Stress-Strain Analysis add-on, you can define a component-dependent limit stress cycle and consider it for the design.
Get a better understanding of the stress distribution within member cross-sections by using clipping planes.
Why are the stresses of the structural analysis different from those calculated with the Stress-Strain Analysis add-on?
The limit stress is activated, but my stress ratio is “non-designable” in the Stress-Strain Analysis add-on. What could be the reason?
Is it possible to display the deformation analysis of a surface (limit 0.5‰)?
I would like to start my calculation in cloud. However, I get the error message "File upload has failed with the error SSL handshake failed." What is the problem?
How can I use an RSECTION cross-section when exporting a model from Revit to RFEM 6?
How can I reduce the calculation time for members with a nonlinear material model in RFEM 6 and RSTAB 9?
