25 Results
View Results:
Sort by:
Question
How can I determine loads at particular geographic coordinates in the online service "Snow Load, Wind Speed, and Seismic Load Maps"?
Question
Is it also possible to integrate the online service "Snow Load, Wind Speed, and Seismic Load Maps" into external applications?
Question
Is the exponent n applied differently from the design standard when determining the damage parameter ζ (zeta)?
Question
How are the location-specific Geo-Zone Tool data queries calculated for the determination of various building loads?
Question
Why is the load value displayed in the online service "Geo-Zone Tool: Snow Load, Wind Speed, and Seismic Load Maps" different from the value in the corresponding standard in some cases?
Question
When designing seismic equivalent loads with a Response Spectra Analysis (RSA) in RFEM, how can I apply the modal response parameters Ie/R according to Sect. 12.9.1.2 in the ASCE‑7‑16 to my results?
Question
Is the Gust-effect (G or Gf) from the ASCE 7‑16 Sect. 26.11 considered in RWIND Simulation?
Question
Is it possible to perform automatic live load reduction in RFEM or RSTAB per the ASCE, IBC, or NBCC?
Question
I am designing a cross-section created in the SHAPE‑THIN program using the design add-on module, but the program shows the error message "ER006 Invalid type of c/t-part for cross-section of type General". What can I do?
In RFEM 6, is it possible to display a graphic with the distribution of the required reinforcement in the DIN A0 format?
In RFEM 6, is it possible to display a graphic with the distribution of the required reinforcement in the DIN A0 format?
ASCE 7 Orthogonal Directional Combination Procedure
How do I apply the ASCE 7 Orthogonal Directional Combination procedure (100% + 30% rule) to my seismic load in a static analysis?
ASCE 7 Seismic Load Combinations
I do not see the seismic load cases in my generated ASCE 7 load combinations (COs). How do I add them?
ASCE 7 Reduced Live Load Factor
My live load is less than or equal to 100 psf. How do I consider the reduced load factor in the ASCE 7 load combinations?
Redundancy Factors
How do I include the redundancy factor(s) ρ in the ASCE 7 load combinations?
Overstrength Factors
How do I include the overstrength factor(s) Ωo in the ASCE 7 load combinations?
Exclude Lateral Torsional Buckling Check
My beam has a continuous lateral support and therefore lateral torsional buckling (LTB) is not a concern. How do I define the effective length?
Standardized Sections for AISI Design
Which standardized sections are valid for AISI cold-formed steel design in RFEM 6?
Custom Sections for AISI Design
Can I design user-defined (parametric) sections according to AISI S100 or CSA S136?
AISI Table B4.1-1 Applicability Limits
Does RFEM check the applicability limits of AISI Table B4.1‑1?
Surface Reinforcement in Rib Design
How do I consider the surface (slab) reinforcement in my rib member (T-beam) design?
- 005437
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Steel Joints for RFEM 6
- Torsional Warping (7 DOF) for RFEM 6
- Torsional Warping (7 DOF) for RSTAB 9
- Steel Structures
- Structural Analysis & Design
- Stress Analysis
- Stability Analysis
- Warping Torsion Analysis
- Steel Connections
- Cold-Formed Sections
- Eurocode 3
- ANSI/AISC 360
- CSA S16
- IS 800
- GB 50017
- SP 63.13330
- BS 5950-1
- AS 4100
- SIA 263
Programs for Steel Structures
Which programs and add-ons are suitable for the structural analysis and design of steel structures?
Programs for Timber Structures
Which Dlubal Software programs can I use to calculate and design timber structures?
Aluminum and Lightweight Structures
I would like to design an aluminum structure. Is it possible to use RFEM or RSTAB for this?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM