27 Results
View Results:
Sort by:
Instability
My model is unstable. What could be the reason?
Question
What are the stiffness reduction factors k33 and k88 in the Multilayer Surfaces Add-on?
Instability
My model is unstable. What could be the reason?
Supports and Loads for Calculation with Warping Torsion
At which point on a cross-section are the supports and loads assumed for the calculation with warping torsion?
Stress Ratio
The limit stress is activated, but my stress ratio is “non-designable” in the Stress-Strain Analysis add-on. What could be the reason?
Cross-Section Warping
How can I display the cross-section warping?
Warping Spring and Warping Restraint
How can I define a warping spring or a warping restraint?
Unstable Model - Troubleshooting
My model in RFEM 6 / RSTAB 9 is unstable. How can I fix it?
Column Failure Modal Analysis
How can I analyze the failure of an object, such as a column, in my modal analysis?
Modal Analysis
How can I display mode shapes in RFEM 6 and RSTAB 9?
Normalization of Mode Shape
Where can I adjust the normalization of a mode shape in RFEM 6 / RSTAB 9?
Warping Release
How do I set a release for warping?
Instability when Using Building Model with "Rigid Diaphragm"
I have a 3D model and try to split it up into "walls" and "surfaces" with the Building Model and to calculate them separately. However, my structural system becomes unstable then. What can be the reason?
Response Spectrum Analysis
How can I perform an earthquake analysis in RFEM 6 and RSTAB 9?
Modal Analysis - Minimum Initial Strain
Why do the results in a modal analysis differ between the initial prestress and the surface load?
Surface Type Error
I received an error message “Surface of incompatible type... (Surface in upper plane of building story must be of ‘Load transfer’ type)” when running the calculation. What is the reason?
Case-Related Design with Different Load Situations
How can I carry out case-related design for different load situations?
- 005113
- Timber Design for RFEM 6
- Timber Design for RSTAB 9
-
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Stress-Strain Analysis for RFEM 6
- Stress-Strain Analysis for RSTAB 9
- Steel Joints for RFEM 6
- Timber Structures
- Concrete Structures
- Steel Structures
- Structural Analysis & Design
- Eurocode 2
- Eurocode 3
- Eurocode 5
- Eurocode 9
Materials of National Annexes
Where can I find the materials for the corresponding National Annexes in RFEM 6 and RSTAB 9?
Construction Stages - Modifying Properties
Is it possible to change the properties of members or surfaces, such as their location, in the individual construction stages?
Analyse de déformation
Is it possible to display the deformation analysis of a surface (limit 0.5‰)?
Deactivating 7th Degree of Freedom by Member
How can I deactivate the 7th degree of freedom for only certain members or cross-sections?
Implausible Results – Torsional Warping
My results of the calculation with Torsional Warping are implausible. What could be the reason?
Neglecting Masses in RFEM 6 / RSTAB 9
How can I neglect masses in my modal analysis in RFEM 6 / RSTAB 9?
Orthotropy Direction for Layers
Why cannot I define a rotation when defining layers?
Stability Analysis with Incrementally Increasing Loading
Can I incrementally increase the load in RFEM 6 or RSTAB 9?
Setting of I-Beam Flange Support for Design in Structure Stability Add-on
In the Steel Design add-on, I have set the boundary conditions in such a way that the I-beam flange is restrained against the horizontal displacement. I then calculated the critical load factors using the Structure Stability add-on, but with no effect on the critical load factor value. What is the reason for this?
- 005437
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Steel Joints for RFEM 6
- Torsional Warping (7 DOF) for RFEM 6
- Torsional Warping (7 DOF) for RSTAB 9
- Steel Structures
- Structural Analysis & Design
- Stress Analysis
- Stability Analysis
- Warping Torsion Analysis
- Steel Connections
- Cold-Formed Sections
- Eurocode 3
- ANSI/AISC 360
- CSA S16
- IS 800
- GB 50017
- SP 63.13330
- BS 5950-1
- AS 4100
- SIA 263