29 Results
View Results:
Sort by:
Different Stresses in Static Analysis and Stress-Strain Analysis
Why are the stresses of the structural analysis different from those calculated with the Stress-Strain Analysis add-on?
Reinforced Concrete Design of Solids
Is it possible to use the add-ons for RFEM 6 to design concrete solids?
Add-ons for Concrete Structures
Which products do you recommend for the structural analysis and design of reinforced concrete structures?
Not Valid/Deactivated Punching Nodes
In the table of the objects to be designed in the Concrete Design add-on, punching nodes are listed in the not valid/deactivated column, although I have defined them as punching nodes. How can I fix this?
Setting of I-Beam Flange Support for Design in Structure Stability Add-on
In the Steel Design add-on, I have set the boundary conditions in such a way that the I-beam flange is restrained against the horizontal displacement. I then calculated the critical load factors using the Structure Stability add-on, but with no effect on the critical load factor value. What is the reason for this?
Graphic Templates for Printing Reinforcement Layout
How can I use graphic templates for multi printing of a reinforcement?
Design Cases
Can I use design cases in RFEM 6 in the same way as in RFEM 5?
Activating Steel Fiber Concrete Design in "Concrete Design" Add-on
How can I activate the design with steel fiber-reinforced concrete in the "Concrete Design" add-on for RFEM 6?
Programs for Concrete Structures
Which programs and add-ons are suitable for concrete structures?
Surface Reinforcement in Rib Design
How do I consider the surface (slab) reinforcement in my rib member (T-beam) design?
Stability Analysis with Incrementally Increasing Loading
Can I incrementally increase the load in RFEM 6 or RSTAB 9?
Instability
My model is unstable. What could be the reason?
How can I check the way RFEM 6 determines the required reinforcement?
How can I check the way RFEM 6 determines the required reinforcement?
Not Covered Reinforcement on Members | Concrete Design in RFEM 6 and RSTAB 9
Although all the member design checks have been fulfilled, I get the "Not Covered Reinforcement" result. What is the reason?
Stress Ratio
The limit stress is activated, but my stress ratio is “non-designable” in the Stress-Strain Analysis add-on. What could be the reason?
Member Design Supports for Deflection Checks
How do I define a member as a cantilever and not as supported at both ends for serviceability or deflection design?
Results of Punching | Concrete design in RFEM 6
Where can I find the graphical results of punching shear in the concrete design? Especially the distribution of shear forces at the critical perimeter or the punching loads.
Instability
My model is unstable. What could be the reason?
Automatic Reinforcement Design
Can the RFEM 6 Concrete Design add-on automatically design member and surface reinforcement?
Nominal Reinforcement Bar Size
Can I define a different bar size in the RFEM 6 Concrete Design add-on other than the default bar sizes available in the drop-down?
Unstable Model - Troubleshooting
My model in RFEM 6 / RSTAB 9 is unstable. How can I fix it?
Punching
I would like to perform punching design of a floor slab. I have selected nodes for the design, but they are marked as invalid. Where did I make a mistake?
Analyse de déformation
Is it possible to display the deformation analysis of a surface (limit 0.5‰)?
Is the deformation analysis in state II included in the concrete design in RFEM 6?
Is the deformation analysis in state II included in the concrete design in RFEM 6?
How can I open the interaction diagram from Concrete Design?
How can I open the interaction diagram from Concrete Design?
Why are the members not valid for the Concrete Design add-on?
Why are the members not valid for the Concrete Design add-on?
Creep and Shrinkage of Concrete
Where can I activate creep or shrinkage for concrete design?
Is it possible to design single-layer reinforced surfaces with RFEM 6?
Is it possible to design single-layer reinforced surfaces with RFEM 6?
- 005113
- Timber Design for RFEM 6
- Timber Design for RSTAB 9
-
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Stress-Strain Analysis for RFEM 6
- Stress-Strain Analysis for RSTAB 9
- Steel Joints for RFEM 6
- Timber Structures
- Concrete Structures
- Steel Structures
- Structural Analysis & Design
- Eurocode 2
- Eurocode 3
- Eurocode 5
- Eurocode 9