36 Wyniki
Wyświetl wyniki:
Sortuj według:
Metoda elementów skończonych oparta na komponentach (CBFEM) w RFEM 6
Co to jest metoda elementów skończonych oparta na komponentach (CBFEM)?
Analiza stateczności zgodnie z EN 1999-1-1
Czy możliwe jest przeprowadzenie analizy stateczności zgodnie z EN 1999-1-1 w RSECTION 1?
Przekrój efektywny
Czy mogę obliczyć efektywne właściwości przekroju za pomocą RSECTION?
- 005450
- RFEM 6
- RSTAB 9
-
- Projektowanie konstrukcji stalowych RFEM 6
- Projektowanie konstrukcji stalowych RSTAB 9
- Projektowanie konstrukcji aluminiowych RFEM 6
- Projektowanie konstrukcji aluminiowych RSTAB 9
- Form-Finding RFEM 6
- Konstrukcje stalowe
- Lekkie konstrukcje aluminiowe
- Konstrukcje tymczasowe
- Rozciągane konstrukcje membranowe
- Analiza statyczno-wytrzymałościowa
- Form-Finding i szablony cięcia
- Analiza dynamiczna i sejsmiczna
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM
Konstrukcje tymczasowe
Chciałbym przeprowadzić analizę konstrukcji tymczasowych. Jakie programy polecacie?
Rusztowania i konstrukcje stelażowe
Wyszukujemy program do rusztowań i konstrukcji stelażowych. Czy nadaje się do tego program Dlubal Software?
Programy do konstrukcji drewnianych warstwowych i klejonych krzyżowo
Jakich programów potrzebuję do pracy z konstrukcjami warstwowymi lub drewnem klejonym krzyżowo (CLT)?
- 005437
- RFEM 6
- RSTAB 9
-
- Projektowanie konstrukcji stalowych RFEM 6
- Projektowanie konstrukcji stalowych RSTAB 9
- Połączenia stalowe RFEM 6
- Skręcanie skrępowane (7 stopni swobody) RFEM 6
- Skręcanie skrępowane (7 stopni swobody) RSTAB 9
- Konstrukcje stalowe
- Analiza statyczno-wytrzymałościowa
- Analiza naprężeń
- Sprawdzenie stateczności
- Analiza skręcania skrępowanego
- Połączenia stalowe
- Profile formowane na zimno
- Eurocode 3
- ANSI/AISC 360
- CSA S16
- IS 800
- GB 50017
- SP 63.13330
- BS 5950-1
- AS 4100
- SIA 263
Programy dla konstrukcji stalowych
Jakie programy i rozszerzenia są odpowiednie do obliczeń i wymiarowania konstrukcji stalowych?
Typy stanów granicznych według AISC 341
Jakie typy stanów granicznych są odpowiednie do obliczeń sejsmicznych wg AISC 341?
Połączenie nakładkowe
Jak utworzyć połączenie typu splot w rozszerzeniu Steel Joints?
Znormalizowane przekroje do obliczeń AISI
Które znormalizowane przekroje są ważne dla obliczeń elementów stalowych AISI formowanych na zimno w programie RFEM 6?
Profile niestandardowe dla AISI Design
Czy mogę zaprojektować przekroje zdefiniowane przez użytkownika (parametryczne) zgodnie z AISI S100 lub CSA S136?
AISI Tabela B4.1-1 Ograniczenia zastosowania
Czy program RFEM sprawdza granice stosowalności tabeli AISI B4.1-1?
AISC 360-16 Płaszczyzna ścinania w gwincie
Czy mogę wykluczyć gwinty śrub z płaszczyzn ścinania zgodnie z AISC 360-16 w rozszerzeniu Połączenia stalowe?
Kierunek ortotropowy dla warstw
Dlaczego'nie mogę zdefiniować obrotu podczas definiowania warstw?
Współczynniki przekroczenia wytrzymałości
Jak uwzględnić współczynnik(i) nadmiernej wytrzymałości Ωo w kombinacjach obciążeń ASCE 7?
Współczynniki redundancji
Jak uwzględnić współczynnik(i) nadmiarowości ρ w kombinacjach obciążeń ASCE 7?
Pytanie
Do obliczenia osiadania w module dodatkowym RF ‑ SOILIN wymagany jest ciężar właściwy gruntu gamma i gamma, sat. Do czego potrzebna jest wartość gamma i jak jest ona uwzględniana w obliczeniach?
Uwzględnienie strefy wpływu ciepła w przypadku aluminium
Czy w module dodatkowym RF-/ALUMINIUM można uwzględnić redukcję wytrzymałości w strefie wpływu ciepła?
Pytanie
Za pomocą modułu dodatkowego RF-/DYNAM Pro wygenerowałem decydujące kombinacje wyników obciążeń sejsmicznych. Jaka jest kolejna procedura wymiarowania poszczególnych elementów konstrukcyjnych?
Pytanie
Po obliczeniach w RF‑/TIMBER Pro, przeprowadziłem optymalizację przekroju. Dlaczego wykorzystanie zoptymalizowanego przekroju jest teraz przekraczane?
Narzędzie do geolokalizacji
Zauważyłem odchylenia od mapy normy DIN EN 1998-1 lub DIN 4149 w serwisie internetowym „ Narzędzie do geolokalizacji: Mapy obciążenia śniegiem, prędkością wiatru i obciążeń sejsmicznych ”. Czy możecie mi powiedzieć, która mapa jest aktualna, a zatem obowiązująca?
Pytanie
Czy w RF-LAMINATE można wyświetlić więcej wartości dla rozkładu naprężeń w warstwach?
- 004727
- RFEM 5
- RSTAB 8
-
- Konstrukcje betonowe
- Konstrukcje stalowe
- Konstrukcje drewniane
- Rozciągane konstrukcje membranowe
- Analiza statyczno-wytrzymałościowa
- Analiza metodą elementów skończonych
- Symulacja przepływu wiatru i generowanie obciążenia wiatrem
- Sprawdzenie stateczności
- Analiza dynamiczna i sejsmiczna
- Form-Finding i szablony cięcia
- Profile formowane na zimno
- Eurocode 1
- Eurocode 3
- Eurocode 5