45 Results
View Results:
Sort by:
Graphic Templates for Printing Reinforcement Layout
How can I use graphic templates for multi printing of a reinforcement?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM
Temporary Structures
I would like to analyze temporary structures. Which programs do you recommend?
Tensile Membrane Structures
Which Dlubal programs do I need for tensile membrane structures?
Cable and Tensile Structures
I would like to analyze cable and tensile structures. Is it possible to use RFEM or RSTAB for this?
Programs for Laminate and CLT Structures
Which programs do I need for laminate and sandwich structures, or cross-laminated timber (CLT)?
Splice Connection
How do I create a splice connection in the Steel Joints add-on?
AISC 360-16 Shear Plane in Thread Option
Can I exclude bolt threads from the shear planes according to AISC 360-16 in the Steel Joints Add-on?
Line Hinges on Several Surfaces
How can I efficiently define line hinges on several surfaces?
Imperfection from Mode Shape
How do I create an imperfection based on a mode shape in RFEM 6?
Welds in RFEM 6
In the case of stairs with a complicated geometry, it is often difficult to design welds by using the analytical methods. How can I do this with RFEM?
Not Covered Reinforcement on Members | Concrete Design in RFEM 6 and RSTAB 9
Although all the member design checks have been fulfilled, I get the "Not Covered Reinforcement" result. What is the reason?
In RFEM 6, is it possible to display a graphic with the distribution of the required reinforcement in the DIN A0 format?
In RFEM 6, is it possible to display a graphic with the distribution of the required reinforcement in the DIN A0 format?
Results of Punching | Concrete design in RFEM 6
Where can I find the graphical results of punching shear in the concrete design? Especially the distribution of shear forces at the critical perimeter or the punching loads.
Is it possible to design single-layer reinforced surfaces with RFEM 6?
Is it possible to design single-layer reinforced surfaces with RFEM 6?
Switching Between Results in Grid Points and Mesh Nodes
Can I switch the required reinforcement in the result tables from "mesh nodes" to "grid points"?
Info Day Online 2018
Are the models and presentations from Info Day 2018 freely available, and can you send them to me?
Question
How can I calculate a timber-concrete composite floor with cross-laminated timber?
Question
How do I create a frame joint with taper in JOINTS Steel - Rigid?
Question
RF‑STEEL AISC add-module shows non-designable results for general cross-sections because of shear buckling checks according to Chapter G. How do I solve this?
Question
How are the signs for the release results of a line release and line hinges interpreted?
Question
How can I perform the design of the tension resistance of a smooth column in a smooth bucket column base; that is, the design against pulling out the column?
- 004727
- RFEM 5
- RSTAB 8
-
- Concrete Structures
- Steel Structures
- Timber Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Finite Element Analysis
- Wind Simulation & Wind Load Generation
- Stability Analysis
- Dynamic and Seismic Analysis
- Form-Finding and Cutting Patterns
- Cold-Formed Sections
- Eurocode 1
- Eurocode 3
- Eurocode 5