30 Results
View Results:
Sort by:
Adjusting NDS and CSA O86 Factors for Consideration in the Timber Design Add-on
How can the NDS and CSA O86 factors be manually adjusted for consideration in the Timber Design add-on?
Reinforced Concrete Design of Solids
Is it possible to use the add-ons for RFEM 6 to design concrete solids?
NDS Strength Configuration - Calculation of Torsion Settings
What calculation is carried out for the NDS Strength Configuration "Calculation of Torsion" options?
Load Extension Isotropic Masonry | Plastic
Is it possible to influence the transverse distribution of a load in the case of the Isotropic | Masonry | Plastic material model?
Add-ons for Concrete Structures
Which products do you recommend for the structural analysis and design of reinforced concrete structures?
Not Valid/Deactivated Punching Nodes
In the table of the objects to be designed in the Concrete Design add-on, punching nodes are listed in the not valid/deactivated column, although I have defined them as punching nodes. How can I fix this?
Graphic Templates for Printing Reinforcement Layout
How can I use graphic templates for multi printing of a reinforcement?
Design Cases
Can I use design cases in RFEM 6 in the same way as in RFEM 5?
Activating Steel Fiber Concrete Design in "Concrete Design" Add-on
How can I activate the design with steel fiber-reinforced concrete in the "Concrete Design" add-on for RFEM 6?
Programs for Laminate and CLT Structures
Which programs do I need for laminate and sandwich structures, or cross-laminated timber (CLT)?
Programs for Timber Structures
Which Dlubal Software programs can I use to calculate and design timber structures?
Programs for Concrete Structures
Which programs and add-ons are suitable for concrete structures?
Surface Reinforcement in Rib Design
How do I consider the surface (slab) reinforcement in my rib member (T-beam) design?
Equivalent Round Section Dimension
How is the dimension for an equivalent round section calculated in the Timber Design add-on?
Instability when Using Building Model with "Rigid Diaphragm"
I have a 3D model and try to split it up into "walls" and "surfaces" with the Building Model and to calculate them separately. However, my structural system becomes unstable then. What can be the reason?
Surface Type Error
I received an error message “Surface of incompatible type... (Surface in upper plane of building story must be of ‘Load transfer’ type)” when running the calculation. What is the reason?
How can I check the way RFEM 6 determines the required reinforcement?
How can I check the way RFEM 6 determines the required reinforcement?
Not Covered Reinforcement on Members | Concrete Design in RFEM 6 and RSTAB 9
Although all the member design checks have been fulfilled, I get the "Not Covered Reinforcement" result. What is the reason?
Member Design Supports for Deflection Checks
How do I define a member as a cantilever and not as supported at both ends for serviceability or deflection design?
Results of Punching | Concrete design in RFEM 6
Where can I find the graphical results of punching shear in the concrete design? Especially the distribution of shear forces at the critical perimeter or the punching loads.
Automatic Reinforcement Design
Can the RFEM 6 Concrete Design add-on automatically design member and surface reinforcement?
Nominal Reinforcement Bar Size
Can I define a different bar size in the RFEM 6 Concrete Design add-on other than the default bar sizes available in the drop-down?
Line Hinge of Slab-Wall Connection
I would like to connect my masonry wall to a reinforced concrete slab. What is the best way to create a line hinge?
Punching
I would like to perform punching design of a floor slab. I have selected nodes for the design, but they are marked as invalid. Where did I make a mistake?
Is the deformation analysis in state II included in the concrete design in RFEM 6?
Is the deformation analysis in state II included in the concrete design in RFEM 6?
How can I open the interaction diagram from Concrete Design?
How can I open the interaction diagram from Concrete Design?
Why are the members not valid for the Concrete Design add-on?
Why are the members not valid for the Concrete Design add-on?
Creep and Shrinkage of Concrete
Where can I activate creep or shrinkage for concrete design?
Is it possible to design single-layer reinforced surfaces with RFEM 6?
Is it possible to design single-layer reinforced surfaces with RFEM 6?
- 005113
- Timber Design for RFEM 6
- Timber Design for RSTAB 9
-
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Stress-Strain Analysis for RFEM 6
- Stress-Strain Analysis for RSTAB 9
- Steel Joints for RFEM 6
- Timber Structures
- Concrete Structures
- Steel Structures
- Structural Analysis & Design
- Eurocode 2
- Eurocode 3
- Eurocode 5
- Eurocode 9