276 Results
View Results:
Sort by:
Stability Analysis of Structural Components with Asymmetric Cross-Section
Is it possible to use the general method according to EN 1993‑1‑1, 6.3.4 to design structural components with an asymmetric cross-section in the Steel Design add-on for RFEM 6 or RSTAB 9?
Add-ons for Concrete Structures
Which products do you recommend for the structural analysis and design of reinforced concrete structures?
Setting of I-Beam Flange Support for Design in Structure Stability Add-on
In the Steel Design add-on, I have set the boundary conditions in such a way that the I-beam flange is restrained against the horizontal displacement. I then calculated the critical load factors using the Structure Stability add-on, but with no effect on the critical load factor value. What is the reason for this?
Pipe as Shear Key in RF-/JOINTS Steel – Column Base Add-on Module
How do I define a pipe as a shear key in RF‑/JOINTS Steel – Column Base add-on module?
Effective Section
Can I calculate the effective section properties of a cross-section using RSECTION?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM
Temporary Structures
I would like to analyze temporary structures. Which programs do you recommend?
Power Plants and Conveyor Structures
Which programs can I use to design power plants and conveyor structures?
Scaffolding and Rack Structures
We are looking for a program for scaffolding and rack structures. Is Dlubal Software suitable for this?
Tensile Membrane Structures
Which Dlubal programs do I need for tensile membrane structures?
Cable and Tensile Structures
I would like to analyze cable and tensile structures. Is it possible to use RFEM or RSTAB for this?
Design of Hydraulic Steel Structures
Can I analyze and design hydraulic steel structures with the Dlubal programs?
- 005437
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Steel Joints for RFEM 6
- Torsional Warping (7 DOF) for RFEM 6
- Torsional Warping (7 DOF) for RSTAB 9
- Steel Structures
- Structural Analysis & Design
- Stress Analysis
- Stability Analysis
- Warping Torsion Analysis
- Steel Connections
- Cold-Formed Sections
- Eurocode 3
- ANSI/AISC 360
- CSA S16
- IS 800
- GB 50017
- SP 63.13330
- BS 5950-1
- AS 4100
- SIA 263
Programs for Steel Structures
Which programs and add-ons are suitable for the structural analysis and design of steel structures?
Standardized Sections for AISI Design
Which standardized sections are valid for AISI cold-formed steel design in RFEM 6?
Custom Sections for AISI Design
Can I design user-defined (parametric) sections according to AISI S100 or CSA S136?
AISI Table B4.1-1 Applicability Limits
Does RFEM check the applicability limits of AISI Table B4.1‑1?
Line Hinges on Several Surfaces
How can I efficiently define line hinges on several surfaces?
Imperfection from Mode Shape
How do I create an imperfection based on a mode shape in RFEM 6?
SLS Rotational Deformations of Crane Runway Girder
Is it possible in the CRANEWAY software to obtain the SLS rotational deformations of a continuous beam at the supports for an isostatic beam in the web plane?
Welds in RFEM 6
In the case of stairs with a complicated geometry, it is often difficult to design welds by using the analytical methods. How can I do this with RFEM?
Implausible Results – Torsional Warping
My results of the calculation with Torsional Warping are implausible. What could be the reason?
User-Defined Material
Can I also use a user-defined material in RF‑/PLATE‑BUCKLING?
Unsymmetrical Cross-Section (UPE)
I am having trouble with the design of a steel structure. For a singly symmetric cross-section (UPE), the program cannot perform the stability analysis. It reports that the Equivalent Member Method 6.3.3 is not applicable for an unsymmetrical cross-section. Is it possible to design such cross-sections in the program?
Adapted Method (Enable Double Bending)
I cannot analyze a UPN cross-section subjected to double bending in the program. Is it possible to do this in the program?
Where can I activate the reduction of load combinations in RFEM 6? And how does this reduction work?
Where can I activate the reduction of load combinations in RFEM 6? And how does this reduction work?
Favorable Permanent Actions
Where can I activate the "Favorable permanent actions" option in RFEM 6 and RSTAB 9 in order to combine the self-weight in the ultimate limit state with 1.0?
Neglecting Torsion
How can I neglect torsion in the steel and timber design?
Fatigue Design
Where is the fatigue design activated in the CRANEWAY program?
Load Transfer Surface RWIND
Is it possible to use load transfer surfaces in RFEM 6 for wind load generation using RWIND?
Combinations for Road Bridges According to EN 1991-2 in RFEM 6
Does RFEM 6 include the combinations for road bridges according to EN 1991‑2?
- 005113
- Timber Design for RFEM 6
- Timber Design for RSTAB 9
-
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Stress-Strain Analysis for RFEM 6
- Stress-Strain Analysis for RSTAB 9
- Steel Joints for RFEM 6
- Timber Structures
- Concrete Structures
- Steel Structures
- Structural Analysis & Design
- Eurocode 2
- Eurocode 3
- Eurocode 5
- Eurocode 9