158 Wyniki
Wyświetl wyniki:
Sortuj według:
Usztywnienia na pasach dźwigarów w połączeniu z ramą sztywną
W jaki sposób usztywnienia na zewnętrznych krawędziach pasów belki połączenia sztywnego ramy wpływają na maksymalny przenoszony moment oraz na sztywność obrotową i powiązane przemieszczenia konstrukcji ramy?
Metoda elementów skończonych oparta na komponentach (CBFEM) w RFEM 6
Co to jest metoda elementów skończonych oparta na komponentach (CBFEM)?
Analiza stateczności zgodnie z EN 1993-1-1
Czy w RSECTION 1 można przeprowadzić analizy stateczności zgodnie z EN 1993-1-1?
Analiza stateczności elementów konstrukcyjnych o niesymetrycznym przekroju
Czy można zastosować metodę ogólną zgodnie z EN 1993-1-1, 6.3.4 do wymiarowania elementów konstrukcyjnych o niesymetrycznym przekroju w module dodatkowym Projektowanie konstrukcji stalowych RFEM 6 lub RSTAB 9?
Ustawianie podpory pasa I dźwigara do obliczeń w rozszerzeniu Stateczność konstrukcji
W ramach rozszerzenia Projektowanie konstrukcji stalowych ustawiłem warunki brzegowe w taki sposób, aby pas I belki był zablokowany podczas poziomego przemieszczenia. Następnie obliczyłem współczynniki obciążenia krytycznego za pomocą rozszerzenia Stateczność konstrukcji, ale współczynnik obciążenia krytycznego nie miał wpływu na podporę. Jaki jest tego powód?
- 005450
- RFEM 6
- RSTAB 9
-
- Projektowanie konstrukcji stalowych RFEM 6
- Projektowanie konstrukcji stalowych RSTAB 9
- Projektowanie konstrukcji aluminiowych RFEM 6
- Projektowanie konstrukcji aluminiowych RSTAB 9
- Form-Finding RFEM 6
- Konstrukcje stalowe
- Lekkie konstrukcje aluminiowe
- Konstrukcje tymczasowe
- Rozciągane konstrukcje membranowe
- Analiza statyczno-wytrzymałościowa
- Form-Finding i szablony cięcia
- Analiza dynamiczna i sejsmiczna
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM
Konstrukcje tymczasowe
Chciałbym przeprowadzić analizę konstrukcji tymczasowych. Jakie programy polecacie?
Rozciągane konstrukcje membranowe
Jakich programów firmy Dlubal potrzebuję do pracy z konstrukcjami membranowymi i membranowymi?
Lekkie konstrukcje aluminiowe
Chciałbym zaprojektować konstrukcję aluminiową. Czy można w tym celu wykorzystać program RFEM lub RSTAB?
- 005443
- RFEM 6
- RSTAB 9
-
- Form-Finding RFEM 6
- Projektowanie konstrukcji aluminiowych RFEM 6
- Projektowanie konstrukcji aluminiowych RSTAB 9
- Konstrukcje stalowe
- Rozciągane konstrukcje membranowe
- Lekkie konstrukcje aluminiowe
- Analiza statyczno-wytrzymałościowa
- Symulacja przepływu wiatru i generowanie obciążenia wiatrem
- Form-Finding i szablony cięcia
- Eurocode 3
- Eurocode 9
Konstrukcje kablowe i poddawane rozciąganiu
Chciałbym przeprowadzić analizę konstrukcji kablowych i sieci kablowych. Czy można w tym celu wykorzystać program RFEM lub RSTAB?
Obliczanie stalowych konstrukcji hydraulicznych
Czy mogę analizować i wymiarować stalowe konstrukcje hydrauliczne za pomocą programów Dlubal?
- 005437
- RFEM 6
- RSTAB 9
-
- Projektowanie konstrukcji stalowych RFEM 6
- Projektowanie konstrukcji stalowych RSTAB 9
- Połączenia stalowe RFEM 6
- Skręcanie skrępowane (7 stopni swobody) RFEM 6
- Skręcanie skrępowane (7 stopni swobody) RSTAB 9
- Konstrukcje stalowe
- Analiza statyczno-wytrzymałościowa
- Analiza naprężeń
- Sprawdzenie stateczności
- Analiza skręcania skrępowanego
- Połączenia stalowe
- Profile formowane na zimno
- Eurocode 3
- ANSI/AISC 360
- CSA S16
- IS 800
- GB 50017
- SP 63.13330
- BS 5950-1
- AS 4100
- SIA 263
Programy dla konstrukcji stalowych
Jakie programy i rozszerzenia są odpowiednie do obliczeń i wymiarowania konstrukcji stalowych?
Typy stanów granicznych według AISC 341
Jakie typy stanów granicznych są odpowiednie do obliczeń sejsmicznych wg AISC 341?
CSA S16 klasa 4 Przekroje
Czy mogę wymiarować pręty z przekrojami klasy 4 zgodnie z CSA S16 w rozszerzeniu Projektowanie konstrukcji stalowych?
Wymiar okrągłego przekroju zastępczego
W jaki sposób obliczany jest wymiar okrągłego przekroju zastępczego w rozszerzeniu Projektowanie konstrukcji drewnianych?
Połączenie nakładkowe
Jak utworzyć połączenie typu splot w rozszerzeniu Steel Joints?
Znormalizowane przekroje do obliczeń AISI
Które znormalizowane przekroje są ważne dla obliczeń elementów stalowych AISI formowanych na zimno w programie RFEM 6?
Profile niestandardowe dla AISI Design
Czy mogę zaprojektować przekroje zdefiniowane przez użytkownika (parametryczne) zgodnie z AISI S100 lub CSA S136?
AISI Tabela B4.1-1 Ograniczenia zastosowania
Czy program RFEM sprawdza granice stosowalności tabeli AISI B4.1-1?
AISC 360-16 Płaszczyzna ścinania w gwincie
Czy mogę wykluczyć gwinty śrub z płaszczyzn ścinania zgodnie z AISC 360-16 w rozszerzeniu Połączenia stalowe?
Wyklucz kontrolę zwichrzenia
Moja belka ma ciągłe podparcie boczne, dlatego wyboczenie skrętne (LTB) nie jest problemem. Jak zdefiniować długość efektywną?
Przeguby liniowe na wielu powierzchniach
Jak skutecznie zdefiniować przeguby liniowe na wielu powierzchniach?
Współczynniki przekroczenia wytrzymałości
Jak uwzględnić współczynnik(i) nadmiernej wytrzymałości Ωo w kombinacjach obciążeń ASCE 7?
Współczynniki redundancji
Jak uwzględnić współczynnik(i) nadmiarowości ρ w kombinacjach obciążeń ASCE 7?
Imperfekcja z postaci własnej
Jak utworzyć imperfekcję w programie RFEM 6 na podstawie postaci własnej?
Nieprawdopodobne wyniki skręcania skrępowanego
Moje wyniki dla obliczeń ze skręcaniem skrępowanym są nieprawdopodobne. Jaka może być tego przyczyna?
Materiał zdefiniowany przez użytkownika
Czy mogę użyć materiału zdefiniowanego przez użytkownika w RF-/PLATE-BUCKLING?
Długości efektywne w obliczaniu stateczności konstrukcji stalowych
Jak zdefiniować długości efektywne podczas wymiarowania prętów stalowych w programie RFEM 6?
Nesymetrický průřez (UPE)
Mám potíž s posouzením ocelové konstrukce. Pro průřez symetrický pouze podle jedné osy (UPE) mi program nechce posoudit stabilitu. Hlasí, že Metoda náhradního prutu podle 6.3.3 není aplikovatelná pro nesymetrický průřez. Lze tyto průřezy v programu posoudit?
Metoda dostosowana (włącz podwójne zginanie)
Nie mogę w programie zanalizować przekroju UPN poddanego podwójnemu zginaniu. Czy można to zrobić w programie?
- 005113
- Projektowanie konstrukcji drewnianych RFEM 6
- Projektowanie konstrukcji drewnianych RSTAB 9
-
- Projektowanie konstrukcji aluminiowych RFEM 6
- Projektowanie konstrukcji aluminiowych RSTAB 9
- Projektowanie konstrukcji stalowych RFEM 6
- Projektowanie konstrukcji stalowych RSTAB 9
- Analiza naprężeniowo-odkształceniowa RFEM 6
- Analiza naprężeniowo-odkształceniowa RSTAB 9
- Połączenia stalowe RFEM 6
- Konstrukcje drewniane
- Konstrukcje betonowe
- Konstrukcje stalowe
- Analiza statyczno-wytrzymałościowa
- Eurocode 2
- Eurocode 3
- Eurocode 5
- Eurocode 9