1199 Results
View Results:
Sort by:
Implementation of Experimental Wind Tunnel Data in RWIND
How we can introduce experimental data in RWIND?
Eccentricity | Axial Offset
How is the axial offset from the adjoining member modeled?
FE Mesh Refinement Factor for Reducing Calculation Time
How can I reduce the calculation time for members with a nonlinear material model in RFEM 6 and RSTAB 9?
Different Stresses in Static Analysis and Stress-Strain Analysis
Why are the stresses of the structural analysis different from those calculated with the Stress-Strain Analysis add-on?
Stability Analysis of Structural Components with Asymmetric Cross-Section
Is it possible to use the general method according to EN 1993‑1‑1, 6.3.4 to design structural components with an asymmetric cross-section in the Steel Design add-on for RFEM 6 or RSTAB 9?
Structure Below Ground Level
Why does the integration/support of my building in the ground below the ground level not work?
Reinforced Concrete Design of Solids
Is it possible to use the add-ons for RFEM 6 to design concrete solids?
Add-ons for Timber Structures
Which Dlubal software products do you recommend for the structural analysis and design of timber structures in particular?
Double-Sided Stiffening (Splice)
How can I model a timber beam with stiffening on both sides? (splice)
Plastic Hinges
How do I define a plastic hinge in RFEM 6?
Importing Surfaces from Rhino into RFEM 6
Why are not all surfaces transferred when importing surfaces from Rhino into RFEM 6?
Add-ons for Concrete Structures
Which products do you recommend for the structural analysis and design of reinforced concrete structures?
Add-ons for Steel Structures
I process steel structures. Which products do you recommend for this area?
State of Development of Beam Panel
What is the current state of development of the "beam panel" element for modeling timber frame walls?
Not Valid/Deactivated Punching Nodes
In the table of the objects to be designed in the Concrete Design add-on, punching nodes are listed in the not valid/deactivated column, although I have defined them as punching nodes. How can I fix this?
Performance Problems on Modern Intel Processors
RFEM calculates more slowly on my new computer than on the old one. What might be the cause, and how can I change it?
Load Transfer Surfaces
The loads from the load transfer surfaces are not displayed. Where are they?
Design Cases
Can I use design cases in RFEM 6 in the same way as in RFEM 5?
Activating Steel Fiber Concrete Design in "Concrete Design" Add-on
How can I activate the design with steel fiber-reinforced concrete in the "Concrete Design" add-on for RFEM 6?
Member Nonlinearity
Is it possible to define member nonlinearities for beam members?
For example, can I define a member that absorbs all internal forces, except for the compressive axial forces?
Are the solids with a common surface automatically connected rigidly to each other?
Are the solids with a common surface automatically connected rigidly to each other?
Is it possible to avoid the login when starting the programs RFEM 6 and RSTAB 9?
Is it possible to avoid the login when starting the programs RFEM 6 and RSTAB 9?
RWIND Calculation Error E315
When performing high-quality transient simulations with a high number of mesh cells, I get this error: "Calculation failed! RWindSolverTransient failed, E315." After that, RWIND stops without results. What can I do?
Steady-State or Transient Simulation for Parapet in RWIND
What is the most accurate CFD method for the wind simulation of parapets?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM