1207 Results
View Results:
Sort by:
SHAPE-THIN 9 Files in RFEM 6 and RSTAB 9
Is it possible to use SHAPE-THIN 9 files in RFEM 6 and RSTAB 9?
Stability Analysis of Structural Components with Asymmetric Cross-Section
Is it possible to use the general method according to EN 1993‑1‑1, 6.3.4 to design structural components with an asymmetric cross-section in the Steel Design add-on for RFEM 6 or RSTAB 9?
Structure Below Ground Level
Why does the integration/support of my building in the ground below the ground level not work?
Reinforced Concrete Design of Solids
Is it possible to use the add-ons for RFEM 6 to design concrete solids?
SHAPE-THIN 9 in Combination with RSTAB 8
Can I use SHAPE-THIN 9 in combination with RSTAB 8?
Add-ons for Timber Structures
Which Dlubal software products do you recommend for the structural analysis and design of timber structures in particular?
Stability Analysis with Torsion
When performing steel design in RFEM 6 or RSTAB 9, I get a warning that the torsion is neglected in the stability design checks. What is the reason for this, and how can I get around the warning message?
Double-Sided Stiffening (Splice)
How can I model a timber beam with stiffening on both sides? (splice)
Fault Tolerant Heap (FTH)
The performance when starting the programs or working in the program has become noticeably worse. What could be the cause of this?
Importing Surfaces from Rhino into RFEM 6
Why are not all surfaces transferred when importing surfaces from Rhino into RFEM 6?
Add-ons for Concrete Structures
Which products do you recommend for the structural analysis and design of reinforced concrete structures?
Add-ons for Steel Structures
I process steel structures. Which products do you recommend for this area?
State of Development of Beam Panel
What is the current state of development of the "beam panel" element for modeling timber frame walls?
Not Valid/Deactivated Punching Nodes
In the table of the objects to be designed in the Concrete Design add-on, punching nodes are listed in the not valid/deactivated column, although I have defined them as punching nodes. How can I fix this?
Load Transfer Surfaces
The loads from the load transfer surfaces are not displayed. Where are they?
Design Cases
Can I use design cases in RFEM 6 in the same way as in RFEM 5?
Activating Steel Fiber Concrete Design in "Concrete Design" Add-on
How can I activate the design with steel fiber-reinforced concrete in the "Concrete Design" add-on for RFEM 6?
Unit Stresses
Can I estimate which minimum cross-sections I should use before starting to design my model?
Pipe as Shear Key in RF-/JOINTS Steel – Column Base Add-on Module
How do I define a pipe as a shear key in RF‑/JOINTS Steel – Column Base add-on module?
Are the solids with a common surface automatically connected rigidly to each other?
Are the solids with a common surface automatically connected rigidly to each other?
Exporting Parametric Cross-Sections from Grasshopper
I get an error when entering the name of a parametric section (for example, R_M1 500/1000) in Grasshopper.
RWIND Calculation Error E315
When performing high-quality transient simulations with a high number of mesh cells, I get this error: "Calculation failed! RWindSolverTransient failed, E315." After that, RWIND stops without results. What can I do?
Incorrect Material or Cross-Section Conversion in Revit or Tekla
I get an incorrect conversion in Tekla/Revit when using regular expressions in the conversion table.
Effective Section
Can I calculate the effective section properties of a cross-section using RSECTION?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM