945 Results
View Results:
Sort by:
Stability Analysis of Structural Components with Asymmetric Cross-Section
Is it possible to use the general method according to EN 1993‑1‑1, 6.3.4 to design structural components with an asymmetric cross-section in the Steel Design add-on for RFEM 6 or RSTAB 9?
Structure Below Ground Level
Why does the integration/support of my building in the ground below the ground level not work?
Version Number of RFEM 6 / RSTAB 9
Where can I find the version number of RFEM 6 / RSTAB 9?
Reinforced Concrete Design of Solids
Is it possible to use the add-ons for RFEM 6 to design concrete solids?
Add-ons for Timber Structures
Which Dlubal software products do you recommend for the structural analysis and design of timber structures in particular?
Result Selection for Design Situation / Result Combination
Why are the maximum deformations not displayed?
Comparative Analysis for RANS, URANS, and DDES Turbulence Models
What is the difference between the RANS, URANS, and DDES turbulence models?
Stability Analysis with Torsion
When performing steel design in RFEM 6 or RSTAB 9, I get a warning that the torsion is neglected in the stability design checks. What is the reason for this, and how can I get around the warning message?
Double-Sided Stiffening (Splice)
How can I model a timber beam with stiffening on both sides? (splice)
Add-ons for Concrete Structures
Which products do you recommend for the structural analysis and design of reinforced concrete structures?
Add-ons for Steel Structures
I process steel structures. Which products do you recommend for this area?
Not Valid/Deactivated Punching Nodes
In the table of the objects to be designed in the Concrete Design add-on, punching nodes are listed in the not valid/deactivated column, although I have defined them as punching nodes. How can I fix this?
Setting of I-Beam Flange Support for Design in Structure Stability Add-on
In the Steel Design add-on, I have set the boundary conditions in such a way that the I-beam flange is restrained against the horizontal displacement. I then calculated the critical load factors using the Structure Stability add-on, but with no effect on the critical load factor value. What is the reason for this?
Graphic Templates for Printing Reinforcement Layout
How can I use graphic templates for multi printing of a reinforcement?
Activating Steel Fiber Concrete Design in "Concrete Design" Add-on
How can I activate the design with steel fiber-reinforced concrete in the "Concrete Design" add-on for RFEM 6?
How can I define temporary supports for a form-finding process in RFEM& 6?
How can I define temporary supports for a form-finding process in RFEM& 6?
Unit Stresses
Can I estimate which minimum cross-sections I should use before starting to design my model?
Member Nonlinearity
Is it possible to define member nonlinearities for beam members?
For example, can I define a member that absorbs all internal forces, except for the compressive axial forces?
RWIND Calculation Error E315
When performing high-quality transient simulations with a high number of mesh cells, I get this error: "Calculation failed! RWindSolverTransient failed, E315." After that, RWIND stops without results. What can I do?
Steady-State or Transient Simulation for Parapet in RWIND
What is the most accurate CFD method for the wind simulation of parapets?
Effective Section
Can I calculate the effective section properties of a cross-section using RSECTION?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM