29 Wyniki
Wyświetl wyniki:
Sortuj według:
- 005599
- RFEM 6
- Projektowanie konstrukcji betonowych RFEM 6
-
- Projektowanie konstrukcji betonowych RSTAB 9
- RSTAB 9
- Projektowanie konstrukcji drewnianych RFEM 6
- Projektowanie konstrukcji drewnianych RSTAB 9
- Projektowanie konstrukcji stalowych RFEM 6
- Projektowanie konstrukcji stalowych RSTAB 9
- Analiza etapów budowy (CSA) dla RFEM 6
- Konstrukcje betonowe
- Konstrukcje stalowe
- Konstrukcje drewniane
- Analiza statyczno-wytrzymałościowa
konfiguracje obliczeniowe mogą się różnić w zależności od przypadku
Jak przeprowadzić wymiarowanie prętów dla różnych ustawień w konfiguracji obliczeniowej?
Analiza statyczna naprężeń różnicowych - naprężenie-odkształcenie
Dlaczego naprężenia dostępne w Analizie statycznej różnią się od tego w rozszerzeniu Analiza naprężeniowo-odkształceniowa?
Konstrukcja poniżej poziomu gruntu
Dlaczego nie działa integracja/podpora mojego budynku w gruncie poniżej górnej krawędzi gruntu?
Obciążenie wydłużenia muru izotropowego | Plastyczne
Czy można odnieść się do poprzecznego rozkładu obciążenia w przypadku izotropowego modelu materiałowego? | Mur | mieć wpływ plastyczny?
Analiza geotechniczna i przypadki obciążeń
Chcę uwzględnić interakcję gruntu z konstrukcją za pomocą jednego z nieliniowych modeli materiałowych gruntu. - Dlaczego obliczanie poszczególnych przypadków obciążeń za pomocą tego modelu nie jest przydatne?
Ustawianie podpory pasa I dźwigara do obliczeń w rozszerzeniu Stateczność konstrukcji
W ramach rozszerzenia Projektowanie konstrukcji stalowych ustawiłem warunki brzegowe w taki sposób, aby pas I belki był zablokowany podczas poziomego przemieszczenia. Następnie obliczyłem współczynniki obciążenia krytycznego za pomocą rozszerzenia Stateczność konstrukcji, ale współczynnik obciążenia krytycznego nie miał wpływu na podporę. Jaki jest tego powód?
Aktywacja rozszerzenia Analiza geotechniczna
Posiadam licencję na rozszerzenie Analiza geotechniczna i wydaje mi się, że jest dostępna. Nie można jednak aktywować rozszerzenia. Jaka może być tego przyczyna?
Ustawianie odkształceń na 0
Jak ustawić odkształcenia z PO/KO lub etapu budowy na 0?
Analiza stateczności ze stopniowym wzrostem obciążenia
Czy mogę stopniowo zwiększać obciążenie w programie RFEM 6 lub RSTAB 9?
Pomijanie mas w programie RFEM 6/RSTAB 9
Jak mogę pominąć masy w analizie modalnej w programie RFEM 6/RSTAB 9?
Mała spójność dla gruntów niespoistych
Jakiej wartości mogę użyć dla spójności, aby uniknąć osobliwości?
Analyse de déformation
Pouvez-vous montrer l’analyse de déformation d’une surface (limite 0,5‰ ) ?
Faza budowy - modyfikacja właściwości
Czy na poszczególnych etapach budowy można zmieniać właściwości prętów lub powierzchni, np. ich położenie?
Wymiarowanie w oparciu o przypadek z różnymi sytuacjami obciążenia
Jak przeprowadzić obliczenia w zależności od przypadku dla różnych sytuacji obciążeniowych?
- 005113
- Projektowanie konstrukcji drewnianych RFEM 6
- Projektowanie konstrukcji drewnianych RSTAB 9
-
- Projektowanie konstrukcji aluminiowych RFEM 6
- Projektowanie konstrukcji aluminiowych RSTAB 9
- Projektowanie konstrukcji stalowych RFEM 6
- Projektowanie konstrukcji stalowych RSTAB 9
- Analiza naprężeniowo-odkształceniowa RFEM 6
- Analiza naprężeniowo-odkształceniowa RSTAB 9
- Połączenia stalowe RFEM 6
- Konstrukcje drewniane
- Konstrukcje betonowe
- Konstrukcje stalowe
- Analiza statyczno-wytrzymałościowa
- Eurocode 2
- Eurocode 3
- Eurocode 5
- Eurocode 9