117 Results
View Results:
Sort by:
Stability Analysis According to EN 1999-1-1
Is it possible to perform stability analysis according to EN 1999‑1‑1 in RSECTION 1?
Adjusting NDS and CSA O86 Factors for Consideration in the Timber Design Add-on
How can the NDS and CSA O86 factors be manually adjusted for consideration in the Timber Design add-on?
NDS Strength Configuration - Calculation of Torsion Settings
What calculation is carried out for the NDS Strength Configuration "Calculation of Torsion" options?
Effective Section
Can I calculate the effective section properties of a cross-section using RSECTION?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM
Temporary Structures
I would like to analyze temporary structures. Which programs do you recommend?
Power Plants and Conveyor Structures
Which programs can I use to design power plants and conveyor structures?
Tensile Membrane Structures
Which Dlubal programs do I need for tensile membrane structures?
Aluminum and Lightweight Structures
I would like to design an aluminum structure. Is it possible to use RFEM or RSTAB for this?
Cable and Tensile Structures
I would like to analyze cable and tensile structures. Is it possible to use RFEM or RSTAB for this?
Standardized Sections for AISI Design
Which standardized sections are valid for AISI cold-formed steel design in RFEM 6?
Custom Sections for AISI Design
Can I design user-defined (parametric) sections according to AISI S100 or CSA S136?
AISI Table B4.1-1 Applicability Limits
Does RFEM check the applicability limits of AISI Table B4.1‑1?
ASD Strength Design in RFEM 6
How can I design my structure according to ASD strength design (such as AISC, ADM, NDS, and so on)?
Earthquake Data in Geo-Zone Tool According to DIN EN 1998
How does the Geo-zone tool determine the earthquake data according to DIN EN 1998‑1?
Generated Seismic Load Combinations
My ASCE 7 generated seismic load combinations combine the X and Y directions in the same CO. How do I change this to independent directions only?
Overstrength Factors
How do I include the overstrength factor(s) Ωo in the ASCE 7 load combinations?
ASCE 7 Reduced Live Load Factor
My live load is less than or equal to 100 psf. How do I consider the reduced load factor in the ASCE 7 load combinations?
Redundancy Factors
How do I include the redundancy factor(s) ρ in the ASCE 7 load combinations?
ASCE 7 Seismic Load Combinations
I do not see the seismic load cases in my generated ASCE 7 load combinations (COs). How do I add them?
Creating Response Spectrum ASCE 7-22
How can I create a response spectrum according to ASCE 7‑22?
ASCE 7 Orthogonal Directional Combination Procedure
How do I apply the ASCE 7 Orthogonal Directional Combination procedure (100% + 30% rule) to my seismic load in a static analysis?
Mode Shapes - Limiting Selection of Shapes
I need many mode shapes to achieve a sum of 90% effective modal mass. Can I limit the number of mode shapes for generating equivalent loads?
Why are new COs generated during the calculation in RF‑/FOUNDATION Pro?
Why are new COs generated during the calculation in RF‑/FOUNDATION Pro?
National Annex DIN EN 1998-1/NA:2021-07
Is the German National Annex 2021‑07 to Eurocode 8 available in RFEM 5 / RSTAB 8?
- 005113
- Timber Design for RFEM 6
- Timber Design for RSTAB 9
-
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Stress-Strain Analysis for RFEM 6
- Stress-Strain Analysis for RSTAB 9
- Steel Joints for RFEM 6
- Timber Structures
- Concrete Structures
- Steel Structures
- Structural Analysis & Design
- Eurocode 2
- Eurocode 3
- Eurocode 5
- Eurocode 9