118 Results
View Results:
Sort by:
Stability Analysis According to EN 1999-1-1
Is it possible to perform stability analysis according to EN 1999‑1‑1 in RSECTION 1?
Effective Section
Can I calculate the effective section properties of a cross-section using RSECTION?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM
Temporary Structures
I would like to analyze temporary structures. Which programs do you recommend?
Power Plants and Conveyor Structures
Which programs can I use to design power plants and conveyor structures?
Tensile Membrane Structures
Which Dlubal programs do I need for tensile membrane structures?
Aluminum and Lightweight Structures
I would like to design an aluminum structure. Is it possible to use RFEM or RSTAB for this?
Cable and Tensile Structures
I would like to analyze cable and tensile structures. Is it possible to use RFEM or RSTAB for this?
- 005437
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Steel Joints for RFEM 6
- Torsional Warping (7 DOF) for RFEM 6
- Torsional Warping (7 DOF) for RSTAB 9
- Steel Structures
- Structural Analysis & Design
- Stress Analysis
- Stability Analysis
- Warping Torsion Analysis
- Steel Connections
- Cold-Formed Sections
- Eurocode 3
- ANSI/AISC 360
- CSA S16
- IS 800
- GB 50017
- SP 63.13330
- BS 5950-1
- AS 4100
- SIA 263
Programs for Steel Structures
Which programs and add-ons are suitable for the structural analysis and design of steel structures?
CSA S16 Class 4 Sections
Can I design members with Class 4 sections according to CSA S16 in the Steel Design add-on?
Standardized Sections for AISI Design
Which standardized sections are valid for AISI cold-formed steel design in RFEM 6?
Custom Sections for AISI Design
Can I design user-defined (parametric) sections according to AISI S100 or CSA S136?
AISI Table B4.1-1 Applicability Limits
Does RFEM check the applicability limits of AISI Table B4.1‑1?
ASD Strength Design in RFEM 6
How can I design my structure according to ASD strength design (such as AISC, ADM, NDS, and so on)?
Earthquake Data in Geo-Zone Tool According to DIN EN 1998
How does the Geo-zone tool determine the earthquake data according to DIN EN 1998‑1?
Generated Seismic Load Combinations
My ASCE 7 generated seismic load combinations combine the X and Y directions in the same CO. How do I change this to independent directions only?
Overstrength Factors
How do I include the overstrength factor(s) Ωo in the ASCE 7 load combinations?
ASCE 7 Reduced Live Load Factor
My live load is less than or equal to 100 psf. How do I consider the reduced load factor in the ASCE 7 load combinations?
Redundancy Factors
How do I include the redundancy factor(s) ρ in the ASCE 7 load combinations?
ASCE 7 Seismic Load Combinations
I do not see the seismic load cases in my generated ASCE 7 load combinations (COs). How do I add them?
Creating Response Spectrum ASCE 7-22
How can I create a response spectrum according to ASCE 7‑22?
ASCE 7 Orthogonal Directional Combination Procedure
How do I apply the ASCE 7 Orthogonal Directional Combination procedure (100% + 30% rule) to my seismic load in a static analysis?
Mode Shapes - Limiting Selection of Shapes
I need many mode shapes to achieve a sum of 90% effective modal mass. Can I limit the number of mode shapes for generating equivalent loads?
Why are new COs generated during the calculation in RF‑/FOUNDATION Pro?
Why are new COs generated during the calculation in RF‑/FOUNDATION Pro?
National Annex DIN EN 1998-1/NA:2021-07
Is the German National Annex 2021‑07 to Eurocode 8 available in RFEM 5 / RSTAB 8?
- 005113
- Timber Design for RFEM 6
- Timber Design for RSTAB 9
-
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Stress-Strain Analysis for RFEM 6
- Stress-Strain Analysis for RSTAB 9
- Steel Joints for RFEM 6
- Timber Structures
- Concrete Structures
- Steel Structures
- Structural Analysis & Design
- Eurocode 2
- Eurocode 3
- Eurocode 5
- Eurocode 9