Obliczenia ze względu na zmęczenie zgodnie z EN 1992-1-1 należy przeprowadzać w przypadku elementów konstrukcyjnych, które są poddane działaniu dużych zakresów naprężeń i/lub wielu zmianom obciążenia. W takim przypadku obliczenia dla betonu i zbrojenia są przeprowadzane osobno. Dostępne są dwie alternatywne metody obliczeniowe.
Rozszerzenie Analiza geotechniczna zapewnia programowi RFEM dodatkowe specyficzne modele materiałowe podłoża, które mogą odpowiednio odwzorować złożone zachowanie materiału podłoża. W tym artykule zaprezentujemy, w jaki sposób można określić zależną od naprężeń sztywność modeli materiałowych gruntu.
Analiza spektrum odpowiedzi jest jedną z najczęściej stosowanych metod obliczeniowych w przypadku obciążenia trzęsieniem ziemi. Metoda ta ma wiele zalet, a najważniejsza z nich to możliwość znacznego uproszczenia obliczeń. Skomplikowany charakter obciążenia jakim jest trzęsienie ziemi jest upraszczany do postaci, która umożliwia przeprowadzenie analizy o rozsądnym stopniu pracochłonności. Wadą metody jest natomiast to, że w wyniku tego uproszczenia traci się część informacji o obciążeniu. Sposobem na zniwelowanie tego ograniczenia może być zastosowanie równoważnej kombinacji liniowej podczas łączenia odpowiedzi modalnych. W poniższym artykule wyjaśniono to bardziej szczegółowo na konkretnym przykładzie.
Jeżeli, na przykład, do określenia sił wewnętrznych ma zostać zastosowany model czysto powierzchniowy, ale wymiarowanie komponentu nadal odbywa się na modelu prętowym, można skorzystać z belki wynikowej.
Program RFEM 6 oferuje rozszerzenie Wymiarowanie aluminium do wymiarowania prętów aluminiowych. W tym artykule pokazano, jak w programie obliczane są przekroje klasy 4 zgodnie z Eurokodem 9.
Podobnie jak w przypadku poprzednich generacji programów firmy Dlubal, zintegrowany interfejs z Autodesk Revit jest teraz dostępny dla programów RFEM 6 i RSTAB 9. W tym artykule przedstawiono ogólne informacje na temat interfejsu oraz obiektów konstrukcyjnych i parametrów związanych z firmą Dlubal w programie Revit.
Niniejszy artykuł jest związany z trwającym projektem, w ramach którego opracowywany i wdrażany jest cyfrowy bliźniak konstrukcyjny mostu Kalix w Szwecji.
W programie RFEM 6 możliwe jest definiowanie wielowarstwowych konstrukcji powierzchniowych za pomocą rozszerzenia „Powierzchnie wielowarstwowe”. Jeżeli zatem rozszerzenie zostało aktywowane w Danych ogólnych modelu, możliwe jest definiowanie konstrukcji warstwowych dla dowolnego modelu materiału. Możliwe jest również łączenie modeli materiałowych, na przykład materiałów izotropowych i ortotropowych.
Przy użyciu specjalnego przegubu liniowego dostępnego w programie RFEM 6 można poprawnie uwzględnić podczas modelowania właściwości połączenia płyty żelbetowej ze ścianą murowaną. Z tego artykułu dowiesz się, jak zdefiniować ten typ przegubu na praktycznym przykładzie.
W tym artykule opisano, jak tworzyć kontakty między dwiema lub większą liczbą równoległych powierzchni poprzez kontrolowanie przenoszenia sił między nimi.
W tym artykule pokazano, jak definiować różne typy usztywnień poprzecznych pręta w programie RFEM 6 i RSTAB 9. Pokazano tu również, w jaki sposób uwzględnić je w projektowaniu i obliczeniach prętów o 7 stopniach swobody.
Z tego artykułu dowiesz się, jak za pomocą rozszerzenia Optymalizacja i koszty/Szacowanie emisji CO₂ do oszacowania kosztów modelu. Ponadto pokazano, w jaki sposób można zoptymalizować parametry w oparciu o minimalny koszt podczas pracy z modelami i blokami sparametryzowanymi.
Programy RFEM i RSTAB zapewniają możliwość wprowadzania sparametryzowanych danych wejściowych, co jest przydatną funkcją produktu do tworzenia lub dostosowywania modeli za pomocą zmiennych. Z tego artykułu dowiesz się, jak definiować parametry globalne i wykorzystywać je we wzorach do określania wartości liczbowych.
Optymalnym scenariuszem, w którym należy zastosować obliczenia wytrzymałości na przebicie, zgodnie z ACI 318-19 lub CSA A23.3:19, jest sytuacja, w której w płycie występuje duża koncentracja obciążeń lub sił reakcji występujących w jednym węźle. W programie RFEM 6 węzeł, w którym występuje przebicie, nazywany jest węzłem z przebiciem. Przyczyny tak dużej koncentracji sił mogą być spowodowane przez słup, siłę skupioną lub podporę węzłową. Łączenie ścian może również powodować obciążenia skupione na końcach, narożach i na końcach obciążeń liniowych i podpór.
Konstrukcje murowe można modelować i analizować w programie RFEM 6 za pomocą rozszerzenia Projektowanie konstrukcji murowych, który wykorzystuje do obliczeń metodę elementów skończonych. Zakładając, że w programie zaimplementowano nieliniowy model materiałowy, można modelować złożone konstrukcje murowe oraz przeprowadzać analizę statyczną i dynamiczną, aby przedstawić nośność konstrukcji murowej oraz różne mechanizmy uszkodzenia. Istnieje możliwość wprowadzania i modelowania konstrukcji murowych bezpośrednio w programie RFEM 6 oraz łączenia modelu materiałowego muru ze wszystkimi popularnymi rozszerzeniami dla programu RFEM. Umożliwia to projektowanie całych modeli budynków w połączeniu z murem.
Zaletą modułu dodatkowego RFEM 6 Steel Joints jest możliwość analizy połączeń stalowych przy użyciu modelu MES, dla którego modelowanie przebiega w pełni automatycznie w tle. Elementy składowe złącza stalowego, które kontrolują modelowanie, można wprowadzić, definiując je ręcznie lub korzystając z dostępnych szablonów w bibliotece. Ta ostatnia metoda została opisana w poprzednim artykule z Bazy wiedzy zatytułowanym „Definiowanie komponentów połączenia stalowego przy użyciu biblioteki”. Definiowanie parametrów do wymiarowania połączeń stalowych jest tematem artykułu w bazie wiedzy „Projektowanie połączeń stalowych w RFEM 6”.
W programie RFEM 6 połączenia stalowe definiuje się jako układ elementów. W nowym rozszerzeniu Połączenia stalowe dostępne są podstawowe komponenty do uniwersalnego zastosowania (blachy, spoiny, płaszczyzny pomocnicze). Metody definiowania połączeń opisano w dwóch poprzednich artykułach w Bazie informacji: „Nowe podejście do wymiarowania połączeń stalowych w programie RFEM 6” oraz „Definiowanie elementów połączenia stalowego przy użyciu biblioteki” .
Modele konstrukcji w programie RFEM 6 można zapisywać jako bloki i wykorzystywać ponownie w innych plikach programu RFEM. Zaletą bloków dynamicznych w porównaniu z blokami nie-dynamicznymi jest to, że umożliwiają interaktywną modyfikację parametrów konstrukcyjnych w wyniku modyfikowania zmiennych wejściowych. Jednym z przykładów jest możliwość dodawania elementów konstrukcyjnych poprzez zmianę tylko liczby przęseł jako zmiennej wejściowej. W tym artykule zademonstrowano taką funkcjonalność dla bloków dynamicznych tworzonych za pomocą skryptów.
Oprócz wstępnie zdefiniowanych modeli dostępnych jako bloki w Dlubal Center | Bloki, możliwe jest tworzenie nowych bloków i zapisywanie ich w sposób opisany w artykule z Bazy wiedzy "Zapisywanie modeli jako bloki w programie RFEM 6".
W programie RFEM 6 można zapisywać wybrane obiekty (a także całe konstrukcje) jako bloki i wykorzystywać je w innych modelach. Istnieją trzy typy bloków: bez parametrów, z parametrami i bloki dynamiczne (z wykorzystaniem JavaScript). W niniejszym artykule przedstawiono pierwszy typ bloku (bez parametrów).
Efekty obciążenia śniegiem są opisane w amerykańskiej normie ASCE/SEI 7-16 oraz w Eurokodzie 1, części od 1 do 3. Normy te zostały zaimplementowane w nowym programie RFEM 6 oraz w Kreatorze obciążenia śniegiem, ułatwiającym wprowadzanie obciążeń śniegiem. Ponadto najnowsza generacja programu umożliwia zdefiniowanie lokalizacji inwestycji na mapie cyfrowej, a tym samym automatyczne zaimportowanie strefy obciążenia śniegiem. Dane te są z kolei wykorzystywane przez Kreatora obciążeń do symulacji efektów spowodowanych obciążeniem śniegiem.
W tym artykule opisano, w jaki sposób płaska płyta budynku mieszkalnego jest modelowana w programie RFEM 6 i wymiarowana zgodnie z Eurokodem 2. Płyta ma grubość 24 cm i jest podparta na słupach o długości 45/45/300 cm w rozstawie co 6,75 m (rysunek 1). Słupy są modelowane jako sprężyste podpory węzłowe poprzez zdefiniowanie sztywności sprężystej na podstawie warunków brzegowych (rysunek 2). Jako materiały wybrano beton C35/45 i stal zbrojeniową B 500 S (A).
Jedną z innowacji w programie RFEM 6 jest nowy sposób projektowania połączeń stalowych. W przeciwieństwie do programu RFEM 5, w którym wymiarowanie połączeń stalowych opiera się na rozwiązaniu analitycznym, rozszerzenie Połączenia stalowe w programie RFEM 6 oferuje rozwiązanie dla połączeń stalowych w oparciu o analizę MES.
Obciążenia eksplozją od materiałów wybuchowych o dużej energii, przypadkowe lub celowe, są rzadkie, ale mogą być wymogiem projektowym. Obciążenia dynamiczne tego typu różnią się od normalnych obciążeń statycznych – są to obciążenia o znacznej wartości, ale oddziałujące bardzo krótkotrwale. Scenariusz eksplozji można przeprowadzić bezpośrednio w programie MES jako analizę historii czasowej, aby zminimalizować utratę żywotności i ocenić różne poziomy uszkodzeń konstrukcji.