Registrieren Sie sich für das Dlubal-Extranet, um die Software optimal nutzen zu lassen und ausschließlichen Zugriff auf Ihre persönlichen Daten zu haben.
Das vorliegende Verifikationsbeispiel beschreibt Druckbelastungen an den Wänden von Gebäuden in Tandemanordnung, die sich in Bodennähe befinden. The buildings are simplified to rectangular objects and scaled down while maintaining the elevation ratios. The pressure distribution on the walls of the model of a medium-high building was conducted by an experiment. The chosen results (pressure coefficient Cp) are compared with the measured values.
A strut with a circular cross-section is supported according to four basic cases of Euler buckling and subjected to pressure force. Ermitteln Sie die Verzweigungslast.
Eine kugelförmige Ballonmembran wird mit Gas mit Atmosphärendruck und definiertem Volumen gefüllt (diese Werte werden nur für die FE-Modelldefinition verwendet). Determine the overpressure inside the balloon due to the given isotropic membrane prestress. The add-on module RF-FORM-FINDING is used for this purpose. Elastic deformations are neglected both in RF-FORM-FINDING and in the analytical solution; self-weight is also neglected in this example.
A thin rectangular orthotropic plate is simply supported and loaded by uniformly distributed pressure. The directions of axes x and y coincide with the principal directions. Bestimmen Sie maximale Durchbiegung der Platte, ohne das Eigengewicht dabei zu berücksichtigen.
A thin circular ring of a rectangular cross-section is exposed to external pressure. Ermitteln Sie die Verzweigungslast und den zugehörigen Lastfaktor für das Knicken in der Ebene.
A two-layered, open-ended, thick-walled vessel is loaded by inner and outer pressure; therefore, there is no axial stress. Es wird die radiale Durchbiegung von Innen- und Außenradius sowie der Druck (radiale Spannung) ermittelt, wobei das Eigengewicht nicht berücksichtigt wird.
A timber beam reinforced by two steel plates at the ends is loaded by pressure. The wood fibers are parallel to the upper loaded side of the beam. Die plastische Oberfläche wird nach der Tsai-Wu-Plastizitätstheorie beschrieben.
Vier Stützen sind unten fixiert und oben durch einen starren Block verbunden. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled by linear elastic material and the inner columns by a stress-strain diagram with decaying dependence. Assuming only the small deformation theory and neglecting the structure's self-weight, determine its maximum deflection.
Bestimmen Sie die maximale Durchbiegung des Kragarms aus zwei Glasscheiben und einer dazwischenliegenden Folienschicht. The plate is fully fixed at one end and subjected to uniform pressure.
Bestimmen Sie die maximale Durchbiegung von vier unten befestigten Stützen, die oben durch einen starren Block verbunden sind. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled as orthotropic elastic material, and the inner columns as orthotropic elastic-plastic material with the same elastic parameters as the outer columns and plasticity properties defined according to the Tsai-Wu plasticity theory.
A timber beam reinforced by two steel plates at the ends is loaded by pressure. The wood fibers are parallel to the upper loaded side of the beam. Die plastische Oberfläche wird nach der Tsai-Wu-Plastizitätstheorie beschrieben.
An beiden Enden ist ein dreidimensionaler Block aus elastisch-plastischem Material mit Verfestigung befestigt. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai‑Wu plasticity theory.
Es soll die maximalen Durchbiegungen des Blockes unter Berücksichtigung bzw. Vernachlässigung der Schubwirkung ermittelt werden. The square block of the isotropic material is fully fixed at one end and loaded with uniform vertical pressure.