Registrieren Sie sich für das Dlubal-Extranet, um die Software optimal nutzen zu lassen und ausschließlichen Zugriff auf Ihre persönlichen Daten zu haben.
A simply supported beam is loaded by pure bending. Aufgrund des Biegeknickens versuchen Sie die Verzweigungslast und den zugehörigen Lastfaktor zu ermitteln.
Eine Membran wird anhand isotroper Vorspannung zwischen zwei Radien von zwei konzentrischen Zylindern gedehnt, die nicht in einer Ebene parallel zur vertikalen Achse liegen. Find the final minimum shape of the membrane - the helicoid - and determine the surface area of the resulting membrane. The add-on module RF-FORM-FINDING is used for this purpose. Elastic deformations are neglected both in RF-FORM-FINDING and in the analytical solution; self-weight is also neglected in this example.
A strut with a circular cross-section is supported according to four basic cases of Euler buckling and subjected to pressure force. Ermitteln Sie die Verzweigungslast.
Berücksichtigen Sie die im Bild Nr.1 dargestellte Stabspannweite ASTM A992 W 18 × 50 und die gleichmäßigen Eigen- und Nutzlasten. The member is limited to a maximum nominal depth of 18 inches. The live load deflection is limited to L/360. The beam is simply supported and continuously braced. Verify the available flexural strength of the selected beam, based on LRFD and ASD.
A thin rectangular orthotropic plate is simply supported and loaded by uniformly distributed pressure. The directions of axes x and y coincide with the principal directions. Bestimmen Sie maximale Durchbiegung der Platte, ohne das Eigengewicht dabei zu berücksichtigen.
Ein gekrümmter Träger besteht aus zwei Trägern mit rechteckigem Querschnitt. The horizontal beam is loaded by distributed loading. While neglecting self-weight, determine the maximum stress on the top surface of the horizontal beam.
Ein Mauerwerk ist in der Mitte seines oberen Querschnitts einer verteilten Last ausgesetzt. The Isotropic Masonry 2D material model is compared with the Isotropic Linear Elastic model, with surface stiffness property Without Tension in the nonlinear calculation.
A structure made of an I-profile is fully fixed on the left end and embedded into the sliding support on the right end. Die Struktur besteht aus zwei Segmenten. The self-weight is neglected in this example. Determine the maximum deflection of the structure, the bending moment on the fixed end, the rotation of segment 2, and the reaction force at point B by means of the geometrically linear analysis and the second-order analysis. The verification example is based on the example introduced by Gensichen and Lumpe.
Stellen wir uns ein biegesteifes Gerüstrohr vor, das durch einen Knotenlager für Gerüst unten befestigt und sowohl durch ein Moment als auch durch eine Kraft belastet wird. Calculate the maximum radial deflection by exceeding the capacity of the scaffolding support.
Eine Struktur aus Stäben mit I-Profilen wird an beiden Enden durch gleitende Federstützen gelagert und durch Transversalkräfte belastet. The self-weight is neglected in this example. Determine the deflection of the structure, the bending moment, the normal force in the given test points, and the horizontal deflection of the spring supports.
A beam is fully fixed (warping is restricted) on the left end and supported by a fork support (warping is enabled) on the right end. The beam is subjected to a torque, longitudinal force, and transverse force. Determine the behavior of the primary torsional moment, secondary torsional moment, and warping moment. Dieses Verifikationsbeispiel basiert auf dem von Gensichen und Lumpe vorgestellten Beispiel.
Ein I-Profil-Kragträger ist am linken Ende gelagert und durch Moment belastet. The aim of this example is to compare the fixed support with the fork support and to investigate the behavior of some representative quantities. Comparison is also made to the solution by means of plates. Small deformations are considered, and the self-weight is neglected. Determine the rotation in the midpoint of the cantilever, and in case of the member entity with warping, determine the values of the primary torsional moment, the secondary torsional moment, and the warping moment both on the left end (point A) and the right end (point B).
An beiden Enden ist ein dreidimensionaler Block aus elastisch-plastischem Material mit Verfestigung befestigt. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai‑Wu plasticity theory.